FRONT DOOR DISASSEMBLY


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A01CBQR

      Disengage the 2 clips and guide, and remove the front door lower frame bracket garnish.

  3. REMOVE LOWER DOOR FRAME GARNISH


    1. A01CFQ1

      Disengage the 3 clips and remove the lower door frame garnish.

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01CDV8

      Using a moulding remover, disengage the 3 claws, and remove the front door inside handle bezel plug.

  5. REMOVE REFLEX REFLECTOR (w/o Courtesy Light)


    1. A01CATKE03

      Using a moulding remover, disengage the claw, and remove the reflex reflector.

    2. Disconnect the connector.

  6. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)


    1. A01CATKE01

      Using a moulding remover, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  7. REMOVE FRONT DOOR PULL HANDLE


    1. A01CBNYE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the claw and open the cover.

    2. A01CDYE

      Remove the screw.

    3. Disengage the 3 claws and remove the front door pull handle.

  8. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01CCX2

      Using a moulding remover, disengage the 9 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector.

  9. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01CC3Z

      Using a moulding remover, disengage the 9 claws.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01CGBP

      Remove the 2 screws.

    2. Using a clip remover, disengage the 12 clips.

    3. Pull out the front door trim board in the direction indicated by the arrow shown in the illustration.

    4. Raise the front door trim board and remove the front door trim board together with the front door inner glass weatherstrip.

    5. for Driver Side with Memory:


      1. Disconnect the connector.

    6. A01CBN8

      Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

  11. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01CFBK

      Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.

  12. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A01CEZP

      Disengage the 9 claws and remove the front door inner glass weatherstrip from the front door panel as shown in the illustration.

  13. REMOVE SEAT MEMORY SWITCH (for Driver Side with Memory)


    1. A01CBBR

      Remove the 2 screws.

    2. Disengage the 4 claws and remove the front door inner glass weatherstrip base.

    3. A01CE6I

      Disengage the 4 claws and remove the seat memory switch.

  14. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY


    1. A01CGFK

      Disconnect the connector.

    2. Drill out the 4 rivet heads using a drill with a bit diameter less than 4 mm (0.158 in.), and remove the front No. 1 speaker assembly.

    3. Use the drill to remove the flange.

      CAUTION:

      Be careful as the cut rivets are very hot.

      Note

      Do not drill the rivets at an angle as this will cause damage to the drill and drill hole. Line up the drill with a rivet, and carefully drill out the rivet head.

    4. Even if the flange is taken off, continue drilling and push out the remaining fragments using the drill.

    5. Using a vacuum cleaner, remove the rivet fragments and shavings from the inside of the door.

  15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER


    1. A01CDDH

      Disconnect the connector.

    2. Remove the 3 nuts.

    3. Disengage the claw and remove the outer rear view mirror assembly with cover.

  16. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side)


    1. A01CCK8

      Disconnect the 2 connectors.

    2. Remove the 2 screws and the outer mirror control ECU assembly.

  17. REMOVE DOOR TRIM BRACKET


    1. A01CCZL

      Disengage the clamp.

    2. Remove the 2 screws and door trim bracket.

  18. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01CFX4

      Disconnect each connector and the 7 clamps.

    2. A01CAM6

      Remove the front door service hole cover.

      Tech Tips

      Remove the remaining butyl tape on the door.

  19. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the power window regulator motor connector.

    3. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

    4. Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

    5. Disconnect the power window regulator motor connector.

    6. A01CDWS

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the door to fall.

    7. A01CDQXE01

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the door glass.

  20. REMOVE FRONT DOOR POWER WINDOW REGULATOR ASSEMBLY


    1. A01CFTJE01

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door power window regulator assembly may fall and get damaged.

    2. Remove the 5 bolts.

    3. Remove the front door power window regulator assembly.

    4. Remove the temporary bolt from the front door power window regulator assembly.

  21. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01CCW2E01

      Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.

      CAUTION:

      Do not place your finger, etc. within the range of movement of the window regulator. When removing the power window regulator motor, the force of the spring causes the window regulator to move in the direction of the arrow shown in the illustration (the direction in which the window rises), which may cause injury.

  22. REMOVE FRONT DOOR GLASS RUN


    1. A01CEN3

      Remove the front door glass run.

  23. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. A01CCXV

      Remove the bolt and front door rear lower frame sub-assembly.

  24. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. A01CEP8

      Remove the hole plug.

    2. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  25. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)


    1. A01CC2C

      Using a screwdriver, disengage the 2 claws and remove the front door outside handle cover.

  26. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. A01CFQM

      Remove the hole plug.

    2. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  27. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. A01CBXV

      Disconnect the connector.

    2. A01CCF1

      Remove the front door outside handle assembly as shown in the illustration.

  28. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD


    1. A01CEOM

      Disengage the 3 claws and remove the front door front outside handle pad.

  29. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD


    1. A01CE26

      Disengage the 2 claws and remove the front door rear outside handle pad.

  30. REMOVE FRONT DOOR LOCK ASSEMBLY


    1. A01CG7M

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.

    3. Remove the door lock wiring harness seal from the front door lock assembly.

  31. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A01CEPB

      Remove the front door lock remote control cable assembly.

  32. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A01CATZ

      Using a screwdriver, disengage the 3 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01CETQ

      Remove the front door inside locking cable assembly.

  33. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. A01CG96

      Disengage the clamp.

    2. A01CDX0

      Using a T30 "TORX" socket wrench, remove the screw.

    3. Disengage the claw and remove the front door outside handle frame sub-assembly.

    4. A01CEBE

      Disconnect the connector.

    5. Disengage the 2 clamps.

  34. REMOVE FRONT DOOR LOCK OPEN ROD


    1. A01CG72E01

      Remove the front door lock open rod as shown in the illustration.

  35. REMOVE DOOR ELECTRICAL KEY OSCILLATOR


    1. A01CE7F

      Remove the screw and door electrical key oscillator.

  36. REMOVE FRONT DOOR CHECK ASSEMBLY


    1. A01CEH7

      Remove the 3 bolts and front door check assembly.

  37. REMOVE FRONT DOOR WEATHERSTRIP


    1. A01CAO1

      Using a clip remover, disengage the 30 clips and remove the front door weatherstrip.

  38. REMOVE FRONT DOOR PANEL CUSHION


    1. A01CD6F

      Disengage the 2 claws and remove the 2 front door panel cushions.

  39. REMOVE FRONT DOOR NO. 2 WEATHERSTRIP


    1. A01CENL

      Using a clip remover, disengage the 6 clips and remove the front door No. 2 weatherstrip.

  40. REMOVE FRONT DOOR WINDOW FRAME MOULDING

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  41. REMOVE FRONT DOOR OUTER GLASS WEATHERSTRIP

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  42. REMOVE FRONT DOOR INNER BLACK OUT TAPE (w/ Black Out Tape)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  43. REMOVE FRONT DOOR OUTER BLACK OUT TAPE (w/ Black Out Tape)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  44. REMOVE FRONT DOOR MUDGUARD SUB-ASSEMBLY (for Standard)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  45. REMOVE FRONT DOOR MUDGUARD SUB-ASSEMBLY (for Sport Package)

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.