Click here

UPPER INSTRUMENT PANEL INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tip:

    It is possible to install the instrument panel register assembly with the upper instrument panel sub-assembly still installed to the vehicle body. Refer to the reassembly procedure for the upper instrument panel sub-assembly.


    1. A01CEGJ

      Engage the 5 claws.

      Note:

      • Do not allow the wire harness to get caught in the claws.

      • Make sure that the claws are fully engaged.

    2. Engage the 9 claws.

    3. Install the 2 clips.

    4. A01CBP0

      Connect the connector.

    5. Install the 2 passenger airbag bolts <A>.

      20 N*m 204 kgf*cm 15 ft.*lbf
    6. A01CC6KE01

      Install the upper instrument panel sub-assembly with the 3 screws <B>.

  2. Click here

    CONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01CFH6

      Connect the connector.

      Note:

      When connecting the airbag connector, take care not to damage the airbag wire harness.

    4. Engage the wire harness clamp.

  3. Click here

    INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    1. A01CE0S

      Engage the 6 claws to install the No. 1 instrument panel box door sub-assembly.

    2. Connect the connector.

  4. Click here

    INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01CC1I

      Engage the 16 claws to install the No. 3 instrument cluster finish panel garnish.

      Note:

      Make sure that the claws are fully engaged.

  5. Click here

    INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD)


    1. A01CBYP

      Engage the 8 claws to install the No. 2 instrument cluster finish panel garnish.

      Note:

      Make sure that the claws are fully engaged.

  6. Click here

    INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD)


    1. A01CFEQ

      Engage the 8 claws to install the No. 2 instrument cluster finish panel garnish.

      Note:

      Make sure that the claws are fully engaged.

  7. Click here

    INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. Connect the connector.

    2. A01CBOAE01

      Engage the 23 claws to install the center instrument cluster finish panel sub-assembly.

      Note:

      • When installing the center instrument cluster finish panel sub-assembly, make sure to press the upper middle part firmly.

      • Make sure that the claws are fully engaged.

    3. Remove the applied protective tape.

    4. Move the shift lever to P.

  8. Click here

    INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01CGCS

      Turn the shift lever knob clockwise to install the shift lever knob sub-assembly.

  9. Click here

    INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01CG2C

      Engage the 15 claws.

      Tip:

      Before engaging the 15 claws, make sure that the claws are positioned correctly.

      Note:

      Make sure that the claws are fully engaged.

    2. Install the instrument cluster finish panel assembly with the bolt <C>.

  10. Click here

    INSTALL INSTRUMENT PANEL BOX ASSEMBLY


    1. A01CEC3E01

      With the instrument panel box assembly opened approximately 60° from its closed position, engage the 2 hinges horizontally.

      Note:

      Engaging the hinges from the top will deform the hinges. Be sure to install the instrument panel box assembly horizontally.

    2. A01CE1FE01

      Install the damper clip.

    3. Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the instrument panel box assembly.

  11. Click here

    INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A01CDTKE01

      With the glove compartment door assembly opened approximately 55° from its closed position, engage the 2 hinges horizontally.

      Note:

      Engaging the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.

    2. A01CDIJE01

      Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.

    3. Engage the claw and connect the glove compartment door stopper.

  12. Click here

    INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. A01CFSFE01

      Engage the 2 guides.

    3. Engage the 4 claws to install the No. 2 instrument panel under cover sub-assembly.

      Note:

      Make sure that the claws are fully engaged.

  13. Click here

    INSTALL CENTER FLOOR CARPET COVER LH


    1. A01CF5Y

      Engage the 4 claws.

    2. A01CG2A

      Install the center floor carpet cover LH with the clip.

  14. Click here

    INSTALL CENTER FLOOR CARPET COVER RH (for RHD)


    1. A01CFS0

      Engage the 4 claws.

    2. A01CDKB

      Install the center floor carpet cover RH with the 2 clips.

  15. Click here

    INSTALL CENTER FLOOR CARPET COVER RH (for LHD)


    1. A01CB02

      Engage the 5 claws.

    2. A01CBO2

      Install the center floor carpet cover RH with the clip.

  16. Click here

    INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. A01CAYP

      Engage the 3 guides and 14 claws.

      Tip:

      Make sure that all claws around the entire circumference of the driver side knee airbag assembly are fully engaged.

      Note:

      Make sure that the claws are fully engaged.

    2. A01CCKN

      Install the lower instrument panel finish panel with the 3 screws <B>.

    3. A01CC11

      Engage the 3 claws and the fuel lid lock control cable assembly.

    4. A01CC18

      Engage the 3 claws and the hood lock control cable assembly.

  17. Click here

    INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)


    1. A01CE7K

      Engage the 3 guides, 13 claws and clip.

      Tip:

      Make sure that all claws around the entire circumference of the driver side knee airbag assembly are fully engaged.

      Note:

      Make sure that the claws are fully engaged.

    2. A01CCWL

      Install the lower instrument panel finish panel with the 3 screws <B>.

    3. A01CGDM

      Connect the fuel filler opening lid lock sub-assembly to the fuel lid lock open lever sub-assembly.

    4. A01CCXK

      Engage the 3 claws and the fuel lid lock control cable assembly.

    5. A01CF0E

      Engage the 3 claws and the hood lock control cable assembly.

  18. Click here

    INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A01CE9Q

      Engage the 2 claws and DLC3.

    2. Engage the clamp.

    3. Connect the connector.

    4. A01CFFK

      Engage the 2 claws and 2 guides.

      Note:

      Make sure that the claws are fully engaged.

    5. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <B>.

  19. Click here

    INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Engage the clamp.

    2. Connect each connector.

    3. A01CCYO

      Engage the 2 claws and guide.

      Note:

      Make sure that the claws are fully engaged.

    4. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <B>.

  20. Click here

    INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Connect the connector.

    2. A01CDHT

      Engage the 4 claws to install the No. 1 instrument cluster finish panel garnish.

  21. Click here

    INSTALL COMBINATION METER ASSEMBLY


    1. A01CFDK

      Connect the connector and temporarily install the combination meter assembly.

      Note:

      When installing the combination meter assembly, do not damage the upper instrument panel sub-assembly and combination meter assembly.

    2. A01CELM

      Engage the 4 claws to install the combination meter assembly.

  22. Click here

    INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL


    1. A01CEO2

      Engage the 11 claws and 2 guides to install the No. 1 instrument cluster finish panel.

    2. A01CDZ6E01

      Remove the protective tape from the steering column cover.

  23. Click here

    INSTALL FRONT LOWER PILLAR GARNISH RH


    1. A01CBM6

      Engage the 4 claws to install the front lower pillar garnish RH.

  24. Click here

    INSTALL FRONT PILLAR GARNISH RH


    1. A01CEH1E02

      Remove the protective cover.

      Table 1. Text in Illustration
      *1 Protective Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly
    2. A01CBGGE01

      Engage the 6 guides and 2 clips to install the front pillar garnish RH.

  25. Click here

    INSTALL NO. 1 ASSIST GRIP (for RH Side)


    1. A01CEGL

      Install the No. 1 assist grip with the 2 bolts.

  26. Click here

    INSTALL ASSIST GRIP PLUG (for Front RH)


    1. A01CDIW

      Engage the 4 claws to install the 2 assist grip plugs.

  27. Click here

    CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01CDCYE02

      Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the front door opening trim weatherstrip RH.

      Table 2. Text in Illustration
      *1 Alignment Mark
      *a White
      Note:

      After installation, check that the corners fit correctly.

  28. Click here

    INSTALL COWL SIDE TRIM BOARD RH (for RHD)


    1. A01CFL6

      Engage the 2 guides, claw and clip to install the cowl side trim board RH.

    2. Install the clip(A).

  29. Click here

    INSTALL COWL SIDE TRIM BOARD RH (for LHD)


    1. A01CE66

      Engage the 2 guides, claw and the 2 clips to install the cowl side trim board RH.

    2. Install the clip(A).

  30. Click here

    INSTALL FRONT LOWER PILLAR GARNISH LH

    Tip:

    Use the same procedure as for the RH side.

  31. Click here

    INSTALL FRONT PILLAR GARNISH LH


    1. A01CGBNE02

      Remove the protective cover.

      Table 3. Text in Illustration
      *1 Protective Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly
    2. A01CBXCE01

      Engage the 6 guides and 2 clips, then install the front pillar garnish LH.

  32. Click here

    INSTALL NO. 1 ASSIST GRIP (for LH Side)

    Tip:

    Use the same procedure as for the RH side.

  33. Click here

    INSTALL ASSIST GRIP PLUG (for Front LH)

    Tip:

    Use the same procedure as for the RH side.

  34. Click here

    CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01CBXAE02

      Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the front door opening trim weatherstrip LH.

      Table 4. Text in Illustration
      *1 Alignment Mark
      *a Yellow Green
      Note:

      After installation, check that the corners fit correctly.

  35. Click here

    INSTALL COWL SIDE TRIM BOARD LH (for RHD)


    1. A01CBNG

      Engage the 2 guides, claw and clip to install the cowl side trim board LH.

    2. Install the clip(A).

  36. Click here

    INSTALL COWL SIDE TRIM BOARD LH (for LHD)


    1. A01CCIK

      Engage the 2 guides, claw and clip to install the cowl side trim board LH.

    2. Install the clip(A).

  37. Click here

    ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  38. Click here

    INSTALL UPPER STEERING COLUMN COVER

    Note:

    Installing the upper steering column cover in the incorrect order may break the claw and cause clearance between the upper steering column cover and lower steering column cover.


    1. A01CC6U

      Engage the 4 clips and the 2 claws to install the upper steering column cover to the lower instrument cover.

    2. A01CE77

      Engage the claw and 2 pins to install the upper steering column cover to the steering column assembly.

  39. Click here

    INSTALL LOWER STEERING COLUMN COVER

    Note:

    Installing the lower steering column cover in the incorrect order may break the claw and cause clearance between the upper steering column cover and lower steering column cover.


    1. A01CAKF

      Engage the 2 claws to install the lower steering column cover to the upper steering column cover.

    2. A01CE69

      Engage the 2 claws.

    3. A01CBF4

      Engage the claw.

      Note:

      Press the area around the claw to engage it.

  40. Click here

    ADJUST SPIRAL CABLE


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01CESJ

      Rotate the spiral cable counterclockwise slowly by hand until it stops.

      Note:

      Do not turn the spiral cable using the airbag wire harness.

    4. A01CC9VE01

      Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

      Note:

      Do not turn the spiral cable using the airbag wire harness.

      Tip:

      The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  41. Click here

    INSTALL STEERING WHEEL ASSEMBLY


    1. A01CBKRE01

      Align the matchmarks on the steering wheel assembly and steering main shaft.

    2. Install the steering wheel assembly set nut.

      50 N*m 510 kgf*cm 37 ft.*lbf

    3. Connect the connectors to the spiral cable sub-assembly.

  42. Click here

    INSTALL STEERING PAD


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01CAO9

      Connect the airbag connector to the steering pad.

      Note:

      When connecting the airbag connector, take care not to damage the airbag wire harness.

    4. Connect the horn connector to the steering pad.

    5. A01CDQ6E01

      Confirm that the circumference groove of each "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

    6. Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

      8.8 N*m 90 kgf*cm 78 in.*lbf
  43. Click here

    INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. A01CBQQ

      Engage the claw to install the lower No. 3 steering wheel cover.

  44. Click here

    INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. A01CEA7

      Engage the claw to install the lower No. 2 steering wheel cover.

  45. Click here

    INSPECT STEERING WHEEL CENTER POINT

  46. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  47. Click here

    INSPECT STEERING PAD


    1. A01CEFY

      Visually check for defects with the steering pad installed on the vehicle.


      1. The defects are as follows:


        • Cuts on the surface and in the grooves of the steering pad

        • Small cracks on the surface and in the grooves of the steering pad

        • Significant discoloration on the surface and in the grooves of the steering pad

        OK
        No defects are found.
        Tip:

        If any of the defects is found, replace the steering pad with a new one.

    2. Make sure that the horn sounds.

      Tip:

      If the horn does not sound, inspect the horn system (Click here).

  48. Click here

    INSPECT SRS WARNING LIGHT

    (Click here)