ROOF HEADLINING REMOVAL


  1. PRECAUTION

    Click here

  2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    1. A01CBQQ

      Disengage the claw to remove the lower No. 3 steering wheel cover.

  5. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    1. A01CEA7

      Disengage the claw to remove the lower No. 2 steering wheel cover.

  6. REMOVE STEERING PAD


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01CBIQE01

      Using a "TORX" socket wrench (T30), loosen the 2 "TORX" screws until the circumference groove catches on the screw case.

    4. A01CBW0

      Pull out the steering pad from the steering wheel assembly.

      Note

      When removing the steering pad, do not pull the airbag wire harness.

    5. A01CG5VE01

      Using a screwdriver with the tip wrapped with protective tape, disconnect the airbag connector from the steering pad.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.

    6. Disconnect the horn connector to remove the steering pad.

  7. REMOVE STEERING WHEEL ASSEMBLY


    1. A01CBKRE01

      Remove the steering wheel assembly set nut.

    2. Put matchmarks on the steering wheel assembly and the steering main shaft.

    3. Disconnect the connectors from the spiral cable.

    4. A01CCZIE01

      Install SST to the steering wheel assembly as shown in the illustration.

      SST
      09950-50013   ( 09951-05010, 09952-05010, 09953-05020, 09954-05070 )

      Note

      Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.

    5. Using SST, remove the steering wheel assembly.

  8. REMOVE LOWER STEERING COLUMN COVER

    Note

    Removing the lower steering column cover in the incorrect order will cause the lower steering column cover to break.


    1. Release the tilt and telescopic lever, and fully extend and lower the steering column assembly.

    2. Lock the tilt and telescopic lever.

    3. A01CGBV

      Push the right and left sides of the lower steering column cover, and disengage the 2 claws.

      Note

      Completely disengage the claws.

    4. A01CCXT

      Use your fingers to disengage the claw through the tilt lever opening on the lower steering column cover.

      Tech Tips

      Spread the claw to disengage it.

    5. A01CD58E01

      Using a screwdriver, insert the tip into each service hole to disengage the 2 claws, and remove the lower steering column cover as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

  9. REMOVE UPPER STEERING COLUMN COVER


    1. A01CD6Q

      Disengage the claw and the 2 pins, and separate the upper steering column cover from the steering column assembly.

    2. A01CC6U

      Disengage the 4 clips and 2 claws to remove the upper steering column cover from the lower instrument cover.

  10. REMOVE COWL SIDE TRIM BOARD RH (for RHD)


    1. A01CFL6

      Remove the clip.

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board RH.

  11. REMOVE COWL SIDE TRIM BOARD RH (for LHD)


    1. A01CE66

      Remove the clip.

    2. Disengage the 2 clips, claw and 2 guides, and remove the cowl side trim board RH.

  12. REMOVE DOOR SCUFF PLATE ASSEMBLY RH


    1. A01CFWN

      Disengage the claw, 6 clips and 3 guides, and remove the door scuff plate assembly RH.

  13. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01CEHZ

      Remove the front door opening trim weatherstrip RH.

  14. REMOVE ASSIST GRIP PLUG (for Front RH)


    1. A01CBSZE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip plugs.

      Tech Tips

      Tape the screwdriver tip before use.

  15. REMOVE NO. 1 ASSIST GRIP (for RH Side)


    1. A01CEGL

      Remove the 2 bolts and the No. 1 assist grip.

  16. REMOVE FRONT PILLAR GARNISH RH


    1. A01CC3AE01

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

    2. Disengage the 6 guides and remove the front pillar garnish RH.

    3. A01CBP2E02
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

        Protective Cover size
        X
        700 mm (27.56 in.)
        Y
        120 mm (4.72 in.)

        Note

        Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish is removed.

  17. REMOVE FRONT LOWER PILLAR GARNISH RH


    1. A01CBM6

      Disengage the 4 claws and remove the front lower pillar garnish RH .

  18. REMOVE REAR DOOR SCUFF PLATE RH


    1. Captain type rear seat:


      1. A01CFIB

        Disengage the 9 claws, 9 clips and 2 guides, and remove the rear door scuff plate RH.

    2. Tip-up type rear seat:


      1. A01CGAPE02
        Text in Illustration
        *1 Protective Tape

        Apply protective tape to the bottom of the seat as shown in the illustration.

      2. A01CEQB

        Using the slide lever, slide the rear No. 1 seat to the rearmost position.

      3. Disengage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration.

        Note

        To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.

      4. A01CETW

        Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.

      5. Disengage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration, and remove the rear door scuff plate RH.

        Note

        To prevent damage to the scuff plate, make sure not to use excessive force when disengaging the clips, claws and guide.

  19. DISCONNECT NO. 1 SLIDE DOOR WEATHERSTRIP RH

  20. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)


    1. A01CG6T

      Disengage the 3 claws to remove the lap belt outer anchor cover.

  21. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH


    1. A01CEG9

      Remove the bolt and disconnect the floor end of the front seat outer belt assembly.

  22. REMOVE ASSIST GRIP PLUG (for Rear RH)


    1. A01CEUWE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip plugs.

      Tech Tips

      Tape the screwdriver tip before use.

  23. REMOVE NO. 2 ASSIST GRIP (for RH Side)


    1. A01CAS5

      Remove the 2 bolts and the No. 2 assist grip.

  24. REMOVE LOWER CENTER PILLAR GARNISH RH


    1. A01CAL9

      Disengage the 4 claws and 3 clips, and remove the lower center pillar garnish RH.

  25. REMOVE UPPER CENTER PILLAR GARNISH RH


    1. A01CBF0

      Using a clip remover, disengage the 2 clips.

    2. A01CBBP

      Disengage the 2 guides and remove the upper center pillar garnish RH.

  26. REMOVE COWL SIDE TRIM BOARD LH (for RHD)


    1. A01CBNG

      Remove the clip(A).

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board LH.

  27. REMOVE COWL SIDE TRIM BOARD LH (for LHD)


    1. A01CCIK

      Remove the clip(A).

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board LH.

  28. REMOVE DOOR SCUFF PLATE ASSEMBLY LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  29. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  30. REMOVE ASSIST GRIP PLUG (for Front LH)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  31. REMOVE NO. 1 ASSIST GRIP (for LH Side)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  32. REMOVE FRONT PILLAR GARNISH LH


    1. A01CC1HE01

      Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

    2. Disengage the 6 guides and remove the front pillar garnish LH.

    3. A01CFHYE02
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a cloth or piece of nylon and secure the ends of the cover with tape as shown in the illustration.

        Protective Cover size
        X
        700 mm (27.56 in.)
        Y
        120 mm (4.72 in.)

        Note

        Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish is removed.

  33. REMOVE FRONT LOWER PILLAR GARNISH LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  34. REMOVE REAR DOOR SCUFF PLATE LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  35. DISCONNECT NO. 1 SLIDE DOOR WEATHERSTRIP LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  36. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  37. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  38. REMOVE ASSIST GRIP PLUG (for Rear LH)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  39. REMOVE NO. 2 ASSIST GRIP (for LH Side)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  40. REMOVE LOWER CENTER PILLAR GARNISH LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  41. REMOVE UPPER CENTER PILLAR GARNISH LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  42. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL


    1. Operate the tilt lever to lower the steering wheel assembly.

    2. A01CDZ6E01

      Apply protective tape to the areas shown in the illustration.

    3. A01CBPO

      Disengage the 4 claws.

    4. A01CAPR

      Disengage the 7 claws and 2 guides to remove the No. 1 instrument cluster finish panel.

  43. REMOVE COMBINATION METER ASSEMBLY


    1. A01CELM

      Disengage the 4 claws.

    2. A01CDME

      Pull the combination meter assembly, disconnect the connector, and remove the combination meter assembly as shown in the illustration.

      Note

      When removing the combination meter assembly, do not damage the upper instrument panel sub-assembly and combination meter assembly.

  44. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01CDHT

      Disengage the 4 claws.

    2. Disconnect the connector and remove the No. 1 instrument cluster finish panel garnish.

  45. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A01CFFK

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and 2 guides.

    3. A01CE9QE01

      Disengage the 2 claws and disconnect the DLC3.

    4. Disengage the clamp.

    5. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  46. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. A01CCYO

      Remove the 2 screws <B>.

    2. Disengage the 2 claws and guide.

    3. Disengage the clamp.

    4. Disconnect each connector and remove the No. 1 instrument panel under cover sub-assembly.

  47. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. A01CC18

      Disengage the 3 claws and disconnect the hood lock control cable assembly.

    2. A01CC11

      Disengage the 3 claws and disconnect the fuel lid lock control cable assembly.

    3. A01CCKN

      Remove the 3 screws <B>.

    4. Disengage the 14 claws and the 3 guides, and remove the lower instrument panel finish panel as shown in the illustration.

      A01CCUJ

      Note


      • Make sure to follow the order shown in the illustration to avoid damage to the lower instrument panel finish panel.

      • While supporting the knee airbag, remove the lower instrument panel finish panel.

  48. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)


    1. A01CF0E

      Disengage the 3 claws and disconnect the hood lock control cable assembly.

    2. A01CCXK

      Disengage the 3 claws and disconnect the fuel lid lock control cable assembly.

    3. A01CGDM

      Disconnect the fuel filler opening lid lock sub-assembly and remove the fuel lid lock open lever sub-assembly.

    4. A01CCWL

      Remove the 3 screws <B>.

    5. Disengage the 13 claws, clip and the 3 guides and remove the lower instrument panel finish panel as shown in the illustration.

      A01CECJ

      Note


      • Make sure to follow the order shown in the illustration to avoid damage to the lower instrument panel finish panel.

      • While supporting the knee airbag, remove the lower instrument panel finish panel.

  49. REMOVE CENTER FLOOR CARPET COVER RH (for RHD)


    1. A01CDKB

      Using a clip remover, remove the 2 clips.

    2. A01CFS0E01

      Disengage the 4 claws and remove the center floor carpet cover RH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover RH while pushing on the instrument cluster finish panel.

  50. REMOVE CENTER FLOOR CARPET COVER RH (for LHD)


    1. A01CBO2

      Using a clip remover, remove the clip.

    2. A01CB02E01

      Disengage the 5 claws and remove the center floor carpet cover RH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover RH while pushing on the instrument cluster finish panel.

  51. REMOVE CENTER FLOOR CARPET COVER LH


    1. A01CG2A

      Using a clip remover, remove the clip.

    2. A01CF5YE01

      Disengage the 4 claws and remove the center floor carpet cover LH in the order shown in the illustration.

      Tech Tips

      Remove the center floor carpet cover LH while pushing on the instrument cluster finish panel.

  52. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Disengage the 4 claws and 2 guides.

      A01CFSFE01

    2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  53. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A01CC1ZE01

      Disengage the claw and release the glove compartment door stopper.

    2. Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the glove compartment door assembly until the stoppers are released.

    3. A01CFV2E01

      Open the glove compartment door assembly to approximately 55° from its closed position. Pull it horizontally toward the rear of the vehicle to disengage the 2 hinges and remove the glove compartment door assembly.

      Note

      Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.

  54. REMOVE INSTRUMENT PANEL BOX ASSEMBLY


    1. A01CD20E01

      Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and pull the instrument panel box assembly until the stoppers are released.

    2. A01CGCYE01

      Open the instrument panel box assembly to approximately 60° from its closed position. Pull it horizontally toward the rear of the vehicle to disengage the 2 hinges and remove the instrument panel box assembly.

      Note

      Pulling the instrument panel box assembly upward to remove it causes the hinges to deform. Be sure to pull out the instrument panel box horizontally.

  55. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01CFL8

      Remove the bolt <C>.

    2. Disengage the 12 claws.

      Tech Tips

      First disengage the 6 claws for the right side and then pull the panel to the rear of the vehicle to disengage the 6 claws for the left side.

    3. A01CD3Y

      Disengage the 3 claws.

    4. Disconnect each connector and remove the instrument cluster finish panel assembly.

  56. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. A01CD4S

      Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.

  57. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. A01CG21E02

      Apply protective tape to the area shown in the illustration.

    2. A01CEQF

      Move the shift lever to N.

    3. Disengage the 3 claws as shown in the illustration.

      Note

      Make sure to disengage the lower claws first. The center instrument cluster finish panel sub-assembly may be damaged if the upper claws are disengaged first.

    4. A01CCCC

      Disengage the 20 claws.

      Note

      Make sure to disengage the lower claws first. The center instrument cluster finish panel sub-assembly may be damaged if the upper claws are disengaged first.

    5. Disconnect the connector and remove the center instrument cluster finish panel sub-assembly.

  58. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD)


    1. A01CBYP

      Disengage the 8 claws and remove the No. 2 instrument cluster finish panel garnish.

      Note

      Disengage the bottom claws first.

  59. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD)


    1. A01CFEQ

      Disengage the 8 claws and remove the No. 2 instrument cluster finish panel garnish.

      Note

      Disengage the bottom claws first.

  60. REMOVE NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01CC1I

      Disengage the 16 claws and remove the No. 3 instrument cluster finish panel garnish.

      Note

      Disengage the bottom claws first.

  61. REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY


    1. A01CD7CE01

      Using a screwdriver, disengage the 6 claws as shown in the illustration.

      Tech Tips

      Pull the door toward the rear of the vehicle while pushing down on the 4 claws at the corners.

      Note


      • When pushing down on the 4 claws, be careful not to damage them. These claws are difficult to disengage.

      • When removing the No. 1 instrument panel box door sub-assembly, make sure to close the lid to avoid damage.

    2. Disconnect the connector and remove the No. 1 instrument panel box door sub-assembly.

  62. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01CBPE

      Disengage the wire harness clamp.

    4. Disconnect the connector.

      Note

      When disconnecting the airbag connector, take care not to damage the airbag wire harness.


      1. A01CDETE01

        Slide the slider to release the lock, and then disconnect the connector.

  63. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Tech Tips

    It is possible to remove the instrument panel register assembly with the upper instrument panel sub-assembly still installed to the vehicle body. Refer to the disassembly procedure for the upper instrument panel sub-assembly.


    1. Remove the 3 screws <B>.

    2. Remove the 2 passenger airbag bolts <A>.

      A01CC6KE01

    3. Using a clip remover, remove the 2 clips.

    4. Disconnect the connector.

    5. Disengage the 9 claws.

      A01CBP0

    6. Disengage the 5 claws and remove the upper instrument panel sub-assembly.

      A01CEGJ

  64. REMOVE BACK DOOR STRIKER COVER


    1. A01CDGVE02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and 2 guides, and remove the back door striker cover.

      Tech Tips

      Tape the screwdriver tip before use.

  65. REMOVE BACK DOOR SCUFF PLATE


    1. A01CCY0

      Remove the 4 claws, 4 clips and 2 guides, and remove the back door scuff plate.

  66. ADJUST REAR NO. 2 SEAT ASSEMBLY RH


    1. A01CE11

      Adjust the rear No. 2 seat assembly so that the positioning marks are aligned as shown in the illustration.

  67. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH


    1. A01CDR9E01

      Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.

  68. REMOVE UPPER SEAT TRACK RAIL COVER RH


    1. A01CC1F

      Disengage the 5 claws and clip.

    2. Disengage the 2 guides and remove the upper seat track rail cover.

    3. A01CFZ1

      Disengage the 2 claws and remove the grommet.

  69. REMOVE NO. 1 SEAT TRACK LOCK PLATE COVER (for RH Side)


    1. A01CDSK

      Disengage the 2 claws, guide and remove the No. 1 seat track lock plate cover.

  70. REMOVE REAR NO. 2 SEAT ASSEMBLY RH


    1. Install the 2 stopper bolts in the order of <B>, <A>.

      A01CC4XE01
      Torque:
      21 N*m  { 214 kgf*cm, 16 ft.*lbf }

      Note

      Use service stopper bolts with part numbers 72702-58120 and 72702-58110, or other bolts of an equivalent size (M8 X 1.25).

      Tech Tips

      Stopper bolts sizes are as shown below.

      Recommended Stopper Bolt
      Part Length
      A 14 mm (0.551 in.)
      B 15.5 mm (0.610 in.) or more
      C 10 mm (0.394 in.) or less
      D 72702-58110 Bolt <A> 45.7 mm (1.80 in.)
      72702-58120 Bolt <B> 61.2 mm (2.41 in.)
      E 72702-58110 Bolt <A> 27.7 mm (1.09 in.)
      72702-58120 Bolt <B> 48.2 mm (1.90 in.)
      F 18 mm (0.709 in.)
      G 2.5 mm (0.0984 in.) or less
      H 1.0 mm (0.0394 in.) or less
      I 0.75 mm (0.0295 in.) or less
      J 5.5 mm (0.217 in.)
    2. A01CBYV

      Remove the 2 nuts and disconnect the rear No. 2 seat outer belt assembly.

    3. Remove the rear No. 2 seat assembly.

      Note

      Do not damage the rear No. 2 seat assembly, body or body interior.

  71. ADJUST REAR NO. 2 SEAT ASSEMBLY LH

    Tech Tips

    Use the same procedure for the RH side and the LH side Click here.

  72. REMOVE RECLINING ADJUSTER RELEASE HANDLE LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  73. REMOVE UPPER SEAT TRACK RAIL COVER LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  74. REMOVE NO. 1 SEAT TRACK LOCK PLATE COVER (for LH Side)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  75. REMOVE REAR NO. 2 SEAT ASSEMBLY LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  76. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01CDVME01

      Turn the No. 1 luggage compartment trim hook clockwise approximately 90° and pull it out as shown in the illustration.

    2. A01CAW1

      Remove the bolt and No. 1 luggage compartment trim hook.

  77. REMOVE ROPE HOOK ASSEMBLY (for RH Side)


    1. A01CE61E02
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 2 claws.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  78. REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER RH (for 60/40 Split Seat Type)


    1. A01CGI2

      Disengage the 4 claws and remove the inner luggage compartment trim cover RH as shown in the illustration.

  79. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH (for 60/40 Split Seat Type)


    1. A01CEZD

      Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.

  80. REMOVE DECK SIDE GARNISH RH


    1. A01CAO7E01

      Disengage the 11 claws and 4 guides, and remove the deck side garnish RH as shown in the illustration.

  81. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY RH


    1. Remove the clip.

    2. Disengage the 14 clips, 7 claws and 2 guides.

    3. Disconnect the connectors, and remove the rear quarter trim panel assembly RH.

      A01CBNX

  82. REMOVE REAR SEAT HOOK SUB-ASSEMBLY RH


    1. A01CB90

      Remove the 2 bolts.

    2. A01CG8H

      Disengage the 4 claws.

    3. A01CE9YE01

      Disengage the 2 guides and remove the rear seat hook sub-assembly RH as shown in the illustration.

  83. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH


    1. A01CD40

      Using a moulding remover, disengage the 2 claws and open the cover.

    2. A01CBQ3

      Loosen the bolt and disconnect the shoulder anchor of the rear No. 2 seat outer belt assembly.

  84. REMOVE UPPER ROOF SIDE INNER GARNISH RH


    1. A01CEA8

      Disengage the 2 clips, claw and guide, and remove the upper roof side inner garnish RH as shown in the illustration.

  85. REMOVE QUARTER LOCK PILLAR GARNISH RH


    1. for 60/40 Split Seat Type:


      1. A01CB61

        Disengage the 3 clips and 2 guides, and remove the quarter lock pillar garnish RH.

    2. except 60/40 Split Seat Type:


      1. A01CFEB

        Disengage the 3 clips and 2 guides, and remove the quarter lock pillar garnish RH.

      2. A01CCZ7

        Disengage the 3 claws and 3 guides from backside of the garnish.

      3. Pull the floor anchor part of the rear No. 1 outer seat belt assembly RH toward the quarter lock pillar garnish RH, and then remove the garnish.

  86. REMOVE FRONT ROOF SIDE RAIL GARNISH RH


    1. A01CF8L

      Using a moulding remover, disengage the 9 claws and 5 clips, and remove the front roof side rail garnish RH as shown in the illustration.

      Note

      Disengage the front clips first.

  87. REMOVE REAR ROOF SIDE RAIL GARNISH RH


    1. A01CBQXE02
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. Disengage the 4 clips and 6 claws, and remove the rear roof side rail garnish RH as shown in the illustration.

      Note

      Disengage the front clips first.

  88. REMOVE REAR NO. 2 SEAT TRACK ASSEMBLY RH


    1. A01CEV0

      Remove the 2 bolts, 2 nuts and the rear No. 2 seat track assembly RH.

  89. REMOVE NO. 1 COOLER AIR DUCT


    1. A01CB8C

      Disengage the 2 claws and remove the cooler plate.

    2. A01CF2A

      Remove the No. 1 cooler air duct as shown in the illustration.

  90. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM HOOK

    Tech Tips

    Use the same procedure for the No. 2 luggage compartment trim hook and No. 1 luggage compartment trim hook.

  91. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  92. REMOVE INNER LUGGAGE COMPARTMENT TRIM COVER LH (for 60/40 Split Seat Type)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  93. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH (for 60/40 Split Seat Type)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  94. REMOVE DECK SIDE GARNISH LH


    1. A01CD2TE01

      Disengage the 12 claws and 4 guides, and remove the deck side garnish LH as shown in the illustration.

  95. REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH


    1. Remove the clip.

    2. Disengage the 15 clips, 8 claws and 2 guides, and remove the rear quarter trim panel assembly LH.

      A01CEOA

  96. REMOVE BACK DOOR CENTER GARNISH (w/ Power Back Door)


    1. A01CDVZ

      Using a moulding remover C, disengage the 6 clips and 4 claws, and remove the back door center garnish.

  97. REMOVE BACK DOOR NO. 2 SERVICE HOLE COVER (w/ Power Back Door)


    1. A01CAW9

      Disengage the 3 claws and remove the back door No. 2 service hole cover.

  98. REMOVE REAR WINDOW SIDE GARNISH LH (w/ Power Back Door)


    1. A01CCJHE01

      Disengage the 3 clips and 2 claws, and remove the rear window side garnish LH.

  99. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door)


    1. A01CFMW

      Remove the 2 bolts and disconnect the power back door rod.

  100. REMOVE REAR SEAT HOOK SUB-ASSEMBLY LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  101. DISCONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  102. REMOVE UPPER ROOF SIDE INNER GARNISH LH


    1. A01CCEU

      Disengage the 2 clips, claw and guide, and remove the upper roof side inner garnish LH as shown in the illustration.

  103. REMOVE QUARTER LOCK PILLAR GARNISH LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  104. REMOVE FRONT ROOF SIDE RAIL GARNISH LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  105. REMOVE REAR ROOF SIDE RAIL GARNISH LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  106. REMOVE INTEGRATION CONTROL AND PANEL ASSEMBLY


    1. A01CDVP

      Using a moulding remover, disengage the claw.

    2. A01CBJC

      Using a moulding remover, disengage the 4 claws and remove the integration control and panel assembly.

    3. Disconnect the connector.

  107. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


    1. A01CG97

      Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.

    2. A01CCWB

      Disengage the 2 claws and remove the inner rear view mirror stay holder cover.

  108. REMOVE RAIN SENSOR COVER (w/ Rain Sensor)


    1. A01CFUFE01

      Disconnect the rain sensor cover as shown in the illustration.

    2. Disengage the 2 claws and remove the rain sensor cover.

  109. REMOVE TELEVISION BASE (w/ Rear Monitor)

    w/o Navigation System for HDD: Click here

    w/ Navigation System for HDD: Click here

  110. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Monitor)

    w/o Navigation System for HDD: Click here

    w/ Navigation System for HDD: Click here

  111. REMOVE ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    Use the same procedure for the other assist grip.


    1. A01CB12E02
      Text in Illustration
      *1 Protective Tape
      *a Allow the cover to come off slightly.

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A01CEFZ

      Disengage the 2 clips and remove the assist grip sub-assembly.

    4. Remove the 2 clips from the vehicle body.

  112. REMOVE REAR ASSIST GRIP ASSEMBLY (w/o Coat Hook)

    Tech Tips

    Use the same procedure for the other rear assist grip.


    1. A01CAVHE01
      Text in Illustration
      *1 Protective Tape
      *a Allow the cover to come off slightly.

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A01CFDB

      Disengage the 2 clips and remove the rear assist grip assembly.

    4. Remove the 2 clips from the vehicle body.

  113. REMOVE REAR ASSIST GRIP ASSEMBLY (w/ Coat Hook)

    Tech Tips

    Use the same procedure for the other rear assist grip.


    1. A01CFKNE04
      Text in Illustration
      *1 Protective Tape
      *a Allow the cover to come off slightly.

      Using a clip remover, disengage the 4 claws.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips


      • Gently pry on the assist grip covers as shown in the illustration to remove them.

      • Tape the clip remover tip before use.

    2. Pull off the 2 assist grip covers by hand.

    3. A01CDGK

      Disengage the 2 clips and remove the rear assist grip assembly.

    4. Remove the 2 clips from the vehicle body.

  114. REMOVE VISOR BRACKET COVER RH


    1. A01CBC4

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover RH.

      Note

      Always replace the visor bracket cover RH with a new one.

  115. REMOVE VISOR ASSEMBLY RH


    1. A01CB3O

      Disengage the 2 clips and remove the visor assembly RH.

    2. A01CCTY

      Remove the 2 visor arm set clips from the vehicle body.

      Note

      Always replace the 2 clips with new ones.

  116. REMOVE VISOR BRACKET COVER LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  117. REMOVE VISOR ASSEMBLY LH

    Tech Tips

    Use the same procedure for the LH side and RH side.

  118. REMOVE VISOR HOLDER


    1. A01CC5ME01

      Turn the visor holder clockwise approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the LH side and RH side.

  119. REMOVE SEAT BELT ANCHOR COVER


    1. A01CF4W

      Disengage the 3 clips, 4 claws and 5 guides, and remove the seat belt anchor cover.

  120. DISCONNECT MAP LIGHT ASSEMBLY


    1. A01CFTS

      Using a moulding remover, disengage the 4 clips and disconnect the map light assembly.

  121. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)


    1. w/ Rain Sensor:


      1. A01CE2F

        Disconnect the connector.

    2. w/ EC Mirror:


      1. A01CER5E01
        Text in Illustration
        *1 w/o Automatic High Beam System
        *2 w/ Automatic High Beam System:

        Disconnect the connector.

    3. Disengage each clamp and disconnect the No. 1 roof wire from the front pillar LH.

    4. Disconnect the 4 No. 1 roof wire connectors from the instrument panel junction block.

    5. Disconnect the No. 2 antenna cord sub-assembly connectors and disengage each clamp from the front pillar RH.

    6. Disconnect the rear No. 2 washer hose from the front pillar RH.

    7. Disconnect the No. 2 antenna cord sub-assembly connector and disengage each clamp from the rear pillar RH.

    8. Disconnect the rear No. 2 washer hose from the rear pillar RH.

      A01CE3G

    9. Disengage the 2 clips and 6 fasteners.

      A01CBYJ
    10. A01CEH9

      Disengage the 2 guides.

    11. A01CCRC

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  122. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)


    1. w/ Rain Sensor:


      1. A01CE2F

        Disconnect the connector.

    2. w/ EC Mirror:


      1. A01CER5E01
        Text in Illustration
        *1 w/o Automatic High Beam System
        *2 w/ Automatic High Beam System:

        Disconnect the connector.

    3. Disengage each clamp and disconnect the No. 1 roof wire from the front pillar LH.

    4. Disconnect the 4 No. 1 roof wire connectors from the instrument panel junction block.

    5. Disconnect the No. 2 antenna cord sub-assembly connectors and disengage each clamp from the front pillar RH.

    6. Disconnect the rear No. 2 washer hose from the front pillar RH.

    7. Disconnect the No. 2 antenna cord sub-assembly connector and disengage each clamp from the rear pillar RH.

    8. Disconnect the rear No. 2 washer hose from the rear pillar RH.

      A01CD5B
    9. A01CDHK

      Disconnect the rear sliding roof drain hose.

      Tech Tips

      Use the same procedure for the LH side and RH side.

    10. Disengage the 2 clips and 28 fasteners.

      A01CBJU
    11. A01CCV5

      Disengage the 2 guides.

    12. A01CDZ8

      Remove the roof headlining assembly from the vehicle through the back door.

      Note

      Do not damage the roof headlining assembly or body interior.

  123. REMOVE REAR SLIDING ROOF DRAIN HOSE RH (w/ Sliding Roof)


    1. A01CB2R

      Remove the rear sliding roof drain hose RH from the sliding roof housing drain end cap RH.

  124. REMOVE REAR SLIDING ROOF DRAIN HOSE LH (w/ Sliding Roof)

    Tech Tips

    Use the same procedure for the LH side and RH side.

  125. REMOVE SLIDING ROOF HOUSING DRAIN END CAP RH (w/ Sliding Roof)


    1. A01CCCG

      Remove the sliding roof housing drain end cap RH.

      Note

      Always replace the rear sliding roof housing drain end cap RH with a new one.

  126. REMOVE SLIDING ROOF HOUSING DRAIN END CAP LH (w/ Sliding Roof)

    Tech Tips

    Use the same procedure for the LH side and RH side.