FRONT SEAT INNER BELT ASSEMBLY (for Power Seat) REMOVAL


  1. REMOVE COWL SIDE TRIM BOARD (for Driver Seat)


    1. A01CFL6

      Remove the clip.

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board RH.

  2. REMOVE FRONT DOOR SCUFF PLATE (for Driver Seat)


    1. A01CFWN

      Disengage the claw, 6 clips and 3 guides, and remove the door scuff plate assembly RH.

  3. REMOVE NO. 3 FLOOR CARPET MOULDING (for Driver Seat)


    1. A01CCSD

      Using a screwdriver, turn the clip 90° counterclockwise to release the 2 locks, and remove the 2 No. 3 floor carpet mouldings.

  4. REMOVE FRONT SEAT LEG COVER (for Driver Seat)


    1. Operate the slide and vertical power seat switch knob and move the seat to the foremost position.

    2. A01CE1V

      Turn back the floor carpet.

    3. A01CF35

      Disengage the 6 claws and guide, and remove the front seat leg cover.

  5. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Driver Seat)

  6. REMOVE FRONT SEAT ASSEMBLY (for Driver Seat)


    1. The seat travel distance can be customized, this function is OFF Click here.

    2. A01CBJR

      Remove the 2 bolts on the rear side of the seat.

    3. Operate the slide and vertical power seat switch knob and move the seat to the rearmost position.

    4. A01CCZSE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    5. A01CBCYE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    6. A01CBCP

      Remove the 2 bolts on the front side of the seat.

    7. Operate the slide and vertical power seat switch knob and move the seat to the center position. Also, operate the reclining power seat switch knob and move the seatback to the upright position.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    9. A01CAQF

      Disconnect the 2 connectors.

    10. A01CFBA

      Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE RECLINING POWER SEAT SWITCH KNOB (for Driver Seat)


    1. A01CC9S

      Using a moulding remover, remove the reclining power seat switch knob.

  8. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB (for Driver Seat)


    1. A01CB8B

      Using a moulding remover, remove the slide and vertical power seat switch knob as shown in the illustration.

  9. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY (for Driver Seat)


    1. A01CEGT

      Disengage the 2 hooks.

    2. A01CBEF

      Remove the 7 screws.

    3. A01CF1N

      Disengage the 8 claws, clip and 4 guides, and remove the front seat cushion shield assembly, No. 2 reclining adjuster inside cover RH and No. 2 reclining adjuster inside cover LH.

  10. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Seat)


    1. A01CC1M

      Disconnect the connector.

    2. Disengage each clamp.

    3. A01CG2S

      Remove the nut and the front seat inner belt assembly.

  11. REMOVE COWL SIDE TRIM BOARD (for Front Passenger Seat)

    for RHD: Click here

    for LHD: Click here

  12. REMOVE FRONT DOOR SCUFF PLATE (for Front Passenger Seat)

    Tech Tips

    Use the same procedure for the LH side and RH side Click here.

  13. REMOVE NO. 3 FLOOR CARPET MOULDING (for Front Passenger Seat)


    1. A01CCWK

      Using a screwdriver, turn the clip 90° counterclockwise to release the 2 locks, and remove the 2 No. 3 floor carpet mouldings.

  14. REMOVE FRONT SEAT LEG COVER (for Front Passenger Seat)


    1. Operate the slide power seat switch knob and move the seat to the foremost position.

    2. A01CBK1

      Turn back the floor carpet.

    3. A01CF94

      Disengage the 6 claws and guide, and remove the front seat leg cover LH.

  15. REMOVE FRONT SEAT HEADREST ASSEMBLY (for Front Passenger Seat)

  16. REMOVE FRONT SEAT ASSEMBLY (for Front Passenger Seat)


    1. A01CCQQ

      Remove the 2 bolts on the rear side of the seat.

    2. Operate the slide power seat switch knob and move the seat to the rearmost position.

    3. A01CCMKE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    4. A01CCEZE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    5. A01CDSZ

      Remove the 2 bolts on the front side of the seat.

    6. Operate the slide power seat switch knob and move the seat to the center position. Also, operate the reclining power seat switch knob and move the seatback to the upright position.

    7. Operate the front seat power seat switch assembly to fully raise the ottoman.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    9. A01CCND

      Disconnect the 2 connectors.

    10. A01CCXM

      Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  17. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Seat)


    1. A01CCTQ

      Remove the 2 screws.

    2. Disengage the 7 claws, clip and 2 guides and remove the front seat inner cushion shield and No. 2 reclining adjuster inside cover RH.

  18. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Seat)


    1. Disconnect each connector.

    2. A01CANQ

      Disengage each clamp.

    3. A01CC1D

      Remove the nut and the front seat inner belt assembly.