FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat) INSTALLATION


  1. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Front Passenger Side)


    1. A01CDEME01

      Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly LH to overlap the protruding parts of the front seat adjuster.

    2. A01CBM3

      Engage each clamp.

    3. Connect each connector.

  2. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Driver Side)


    1. A01CFIME01

      Install the front seat inner belt assembly RH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding parts of the front seat adjuster.

    2. A01CBXG

      Engage each clamp.

    3. Connect the connector.

  3. INSTALL FRONT SEAT INNER CUSHION SHIELD


    1. A01CAMN

      Engage the guide.

    2. Engage the clip and the claw.

    3. Install the front seat inner cushion shield with the screw.

  4. INSTALL FRONT SEAT ASSEMBLY


    1. A01CDOK

      Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A01CAQF

      Connect each connector.

    3. Temporarily install the front seat assembly with the 4 bolts.

    4. Lift up the seat track adjusting handle and move the seat to the rearmost position.

    5. A01CEGBE01

      Tighten the 2 bolts on the front side of the seat.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

    6. A01CBYK

      Engage the 2 claws and the guide to close the cover.

    7. A01CB6N

      Engage the 2 claws and the guide to close the cover.

    8. Lift up the seat track adjusting handle and move the seat to the foremost position.

    9. A01CBJRE01

      Tighten the 2 bolts on the rear side of the seat.

      Torque:
      39 N*m  { 398 kgf*cm, 29 ft.*lbf }

      Tech Tips

      Tighten the bolts in the order indicated in the illustration.

  5. INSPECT FOR FRONT SEAT SLIDE ADJUSTER LOCKS


    1. During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.

  6. INSTALL FRONT SEAT HEADREST ASSEMBLY

  7. INSTALL FRONT SEAT LEG COVER


    1. A01CF35

      Engage the 6 claws and the guide to install the front seat leg cover.

    2. A01CEMJ

      Install the floor carpet.

  8. INSTALL NO. 3 FLOOR CARPET MOULDING


    1. A01CGEM

      Engage the 2 clips and install the 2 No. 3 floor carpet mouldings.

  9. INSTALL FRONT DOOR SCUFF PLATE


    1. A01CFWN

      Engage the 3 guides, claw and 6 clips to install the door scuff plate assembly RH.

  10. INSTALL COWL SIDE TRIM BOARD


    1. A01CFL6

      Engage the 2 guides, claw and clip to install the cowl side trim board RH.

    2. Install the clip(A).

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.

  13. INSPECT SEAT BELT WARNING SYSTEM


    1. Inspect the seat belt warning system Click here.