Click here

POWER SEAT SWITCH (for Driver Seat) REMOVAL

Click here
Click here Click here
  1. Click here

    REMOVE COWL SIDE TRIM BOARD LH (for LHD)


    1. A01CCIK

      Remove the clip(A).

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board LH.

  2. Click here

    REMOVE COWL SIDE TRIM BOARD RH (for RHD)


    1. A01CFL6

      Remove the clip.

    2. Disengage the clip, claw and 2 guides, and remove the cowl side trim board RH.

  3. Click here

    REMOVE DOOR SCUFF PLATE ASSEMBLY RH


    1. A01CFWN

      Disengage the claw, 6 clips and 3 guides, and remove the door scuff plate assembly RH.

  4. Click here

    REMOVE NO. 3 FLOOR CARPET MOULDING


    1. A01CCSD

      Using a screwdriver, turn the clip 90° counterclockwise to release the 2 locks, and remove the 2 No. 3 floor carpet mouldings.

  5. Click here

    REMOVE FRONT SEAT LEG COVER RH


    1. Operate the slide and vertical power seat switch knob and move the seat to the foremost position.

    2. A01CE1V

      Turn back the floor carpet.

    3. A01CF35

      Disengage the 6 claws and guide, and remove the front seat leg cover.

  6. Click here

    REMOVE FRONT SEAT HEADREST ASSEMBLY

  7. Click here

    REMOVE FRONT SEAT ASSEMBLY


    1. The seat travel distance can be customized, this function is OFF (Click here).

    2. A01CBJR

      Remove the 2 bolts on the rear side of the seat.

    3. Operate the slide and vertical power seat switch knob and move the seat to the rearmost position.

    4. A01CCZSE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    5. A01CBCYE01

      Using a screwdriver wrapped with protective tape, disengage the 2 claws and guide, and open the cover.

    6. A01CBCP

      Remove the 2 bolts on the front side of the seat.

    7. Operate the slide and vertical power seat switch knob and move the seat to the center position. Also, operate the reclining power seat switch knob and move the seatback to the upright position.

    8. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    9. A01CAQF

      Disconnect the 2 connectors.

    10. A01CFBA

      Remove the front seat assembly.

      Note:

      Be careful not to damage the vehicle body.

  8. Click here

    REMOVE RECLINING POWER SEAT SWITCH KNOB


    1. A01CC9S

      Using a moulding remover, remove the reclining power seat switch knob.

  9. Click here

    REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. A01CB8B

      Using a moulding remover, remove the slide and vertical power seat switch knob as shown in the illustration.

  10. Click here

    REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    1. A01CEGT

      Disengage the 2 hooks.

    2. A01CBEF

      Remove the 7 screws.

    3. A01CF1N

      Disengage the 8 claws, clip and 4 guides, and remove the front seat cushion shield assembly, No. 2 reclining adjuster inside cover RH and No. 2 reclining adjuster inside cover LH.

  11. Click here

    REMOVE POSITION CONTROL ECU AND SWITCH ASSEMBLY


    1. A01CFYD

      Remove the 3 screws.

    2. Disconnect the 2 connectors and remove the position control ECU and switch assembly.