REAR AIRBAG SENSOR INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the RH side.


  1. INSTALL REAR AIRBAG SENSOR


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01CCVU

    4. Insert the pin (stopper) into the body hole and install the rear airbag sensor assembly to the vehicle body with the nut.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the rear airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the rear airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Make sure that the pin (stopper) is securely inserted into the body hole.

      • Tighten the nut while holding the rear airbag sensor assembly because the rear airbag sensor assembly pin (stopper) is easily damaged.

    5. Connect the connector to the rear airbag sensor assembly.

      A01CEZBE01
      Text in Illustration
      *1 CPA - -
      *a Slide - -

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.


      1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Tech Tips

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.

    6. Check that there is no looseness in the installation parts of the rear airbag sensor assembly.

  2. INSTALL REAR QUARTER TRIM PANEL ASSEMBLY


    1. Connect the connectors.

    2. Engage the 2 guides, 7 claws and 14 clips to install the rear quarter trim panel assembly RH.

    3. Install the clip(A).

      A01CBNX

  3. INSTALL DECK SIDE GARNISH


    1. A01CC0RE01

      Engage the 4 guides and 11 claws to install the deck side garnish RH as shown in the illustration.

  4. INSTALL ROPE HOOK ASSEMBLY


    1. A01CB2D

      Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

    2. Engage the 2 claws.

  5. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01CAW1

      Install the bolt.

    2. A01CAXYE01

      Push in the No. 1 luggage compartment trim and turn it clockwise approximately 90° to install the No. 1 luggage compartment trim hook.

  6. INSTALL REAR NO. 2 SEAT ASSEMBLY

    Tech Tips

    Refer to the instructions for Installation of the rear No. 2 seat assembly Click here.

  7. INSTALL BACK DOOR SCUFF PLATE


    1. A01CCY0

      Engage the 2 guides, 4 clips and 4 claws to install the back door scuff plate.

  8. INSTALL BACK DOOR STRIKER COVER


    1. A01CEXU

      Engage the 2 guides and 4 claws to install the back door striker cover.

  9. CONNECT NO. 1 SLIDE DOOR WEATHERSTRIP


    1. A01CBO3E02
      Text in Illustration
      *1 Alignment Mark
      *a Pink
      *b White

      Align the alignment marks on the weatherstrip with the protruding portions on the body indicated by the arrows in the illustration, and install the No. 1 slide door weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  10. INSTALL REAR DOOR SCUFF PLATE


    1. Captain type rear seat:


      1. A01CFIB

        Engage the 2 guides, 9 clips and 9 claws to install the rear door scuff plate RH.

    2. Tip-up type rear seat:


      1. A01CETW

        Using the reclining lever or foot-operated walk-in pedal, tip up the rear No. 1 seat and slide it to the foremost position.

      2. Engage the 5 clips, 4 claws and guide on the rear side of the scuff plate as shown in the illustration.

      3. A01CEQB

        Using the slide lever, slide the rear No. 1 seat to the rearmost position.

      4. Engage the 4 clips, 5 claws and guide on the front side of the scuff plate as shown in the illustration to install the rear door scuff plate RH.

      5. A01CGAPE02
        Text in Illustration
        *1 Protective Tape

        Remove the protective tape applied to the bottom of the rear seat.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. PERFORM DIAGNOSTIC SYSTEM CHECK


    1. Perform a diagnostic system check Click here.

  13. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.