ENTRY LOCK AND UNLOCK SWITCH INSTALLATION


  1. INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. A01CBD7

      Insert the front end of the front door outside handle assembly into the front door outside handle frame.

    2. Insert the rear end of the front door outside handle assembly into the front door outside handle frame. Next, slide the front door outside handle assembly toward the front of the vehicle to install it.

    3. A01CBXV

      Connect the connector.

  2. INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. A01CDIL

      Install the front door outside handle cover with lock cylinder assembly into the front door.

    2. A01CEP8

      Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    3. Install the hole plug.

  3. INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. A01CFQM

      Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Install the hole plug.

  4. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply butyl tape to the front door panel.

    2. Pass the front door lock remote control cable and front door inside the locking cable through a new front door service hole cover.

    3. A01CCGGE01

      Attach the front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover avoiding wrinkles and air bubbles.

    4. A01CFX4

      Connect each connector.

    5. Engage the 7 clamps.

  5. INSTALL DOOR TRIM BRACKET


    1. A01CCZL

      Install the door trim bracket with the 2 screws.

    2. Engage the clamp to the door trim bracket.

  6. INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side)


    1. A01CCK8

      Install the outer mirror control ECU assembly with the 2 screws.

    2. Connect the 2 connectors.

  7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. for Driver Side with Memory:


      1. Connect the connector.

    2. A01CCLL

      Engage the 12 clips and install the front door trim board sub-assembly to the front door panel.

    3. Install the 2 screws.

  8. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. Connect the connector.

    2. A01CF7S

      Engage the 9 claws to install the power window regulator master switch assembly with front door armrest base panel.

  9. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01CDUJ

      Connect the connector.

    2. Engage the 9 claws to install the power window regulator switch assembly with front door armrest base panel.

  10. INSTALL FRONT DOOR PULL HANDLE


    1. A01CDYE

      Engage the 3 claws.

    2. Install the front door pull handle with the screw.

    3. A01CCQE

      Engage the claw and close the cover.

  11. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01CCM7E01

      Engage the claw to install the courtesy light assembly.

  12. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01CBSH

      Engage the 3 claws to install the front door inside handle bezel plug.

  13. INSTALL LOWER DOOR FRAME GARNISH


    1. A01CFQ1

      Engage the 3 clips to install the lower door frame garnish.

  14. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A01CBQR

      Engage the guide and 2 clips to install the front door lower frame bracket garnish.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)

    Click here