ENTRY LOCK AND UNLOCK SWITCH REMOVAL


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  2. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A01CBQR

      Disengage the 2 clips and guide, and remove the front door lower frame bracket garnish.

  3. REMOVE LOWER DOOR FRAME GARNISH


    1. A01CFQ1

      Disengage the 3 clips and remove the lower door frame garnish.

  4. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01CDV8

      Using a moulding remover, disengage the 3 claws, and remove the front door inside handle bezel plug.

  5. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01CATKE01

      Using a moulding remover, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  6. REMOVE FRONT DOOR PULL HANDLE


    1. A01CBNYE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the claw and open the cover.

    2. A01CDYE

      Remove the screw.

    3. Disengage the 3 claws and remove the front door pull handle.

  7. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01CCX2

      Using a moulding remover, disengage the 9 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector.

  8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01CC3Z

      Using a moulding remover, disengage the 9 claws.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01CGBP

      Remove the 2 screws.

    2. Using a clip remover, disengage the 12 clips.

    3. Pull out the front door trim board in the direction indicated by the arrow shown in the illustration.

    4. Raise the front door trim board and remove the front door trim board together with the front door inner glass weatherstrip.

    5. for Driver Side with Memory:


      1. Disconnect the connector.

    6. A01CBN8

      Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

  10. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side)


    1. A01CCK8

      Disconnect the 2 connectors.

    2. Remove the 2 screws and the outer mirror control ECU assembly.

  11. REMOVE DOOR TRIM BRACKET


    1. A01CCZL

      Disengage the clamp.

    2. Remove the 2 screws and door trim bracket.

  12. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01CFX4

      Disconnect each connector and the 7 clamps.

    2. A01CAM6

      Remove the front door service hole cover.

      Tech Tips

      Remove the remaining butyl tape on the door.

  13. REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. A01CEP8

      Remove the hole plug.

    2. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  14. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)


    1. A01CFQM

      Remove the hole plug.

    2. Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

      Tech Tips

      The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.

  15. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY


    1. A01CBXV

      Disconnect the connector.

    2. A01CCF1

      Remove the front door outside handle assembly as shown in the illustration.