Click here

FRONT DOOR LOCK REMOVAL

Click here
Click here Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A01CBQR

      Disengage the 2 clips and guide, and remove the front door lower frame bracket garnish.

  4. Click here

    REMOVE LOWER DOOR FRAME GARNISH


    1. A01CDV8

      Using a moulding remover, disengage the 3 claws, and remove the front door inside handle bezel plug.

  5. Click here

    REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01CDV8

      Using a moulding remover, disengage the 3 claws, and remove the front door inside handle bezel plug.

  6. Click here

    REMOVE REFLEX REFLECTOR (w/o Courtesy Light)


    1. A01CATKE03

      Using a moulding remover, disengage the claw, and remove the reflex reflector.

    2. Disconnect the connector.

  7. Click here

    REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)


    1. A01CATKE01

      Using a moulding remover, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  8. Click here

    REMOVE FRONT DOOR PULL HANDLE


    1. A01CBNYE01

      Using a screwdriver with the tip wrapped with protective tape, disengage the claw and open the cover.

    2. A01CDYE

      Remove the screw.

    3. Disengage the 3 claws and remove the front door pull handle.

  9. Click here

    REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01CCX2

      Using a moulding remover, disengage the 9 claws and remove the power window regulator master switch assembly with front door armrest base panel.

    2. Disconnect the connector.

  10. Click here

    REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01CC3Z

      Using a moulding remover, disengage the 9 claws.

    2. Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.

  11. Click here

    REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01CGBP

      Remove the 2 screws.

    2. Using a clip remover, disengage the 12 clips.

    3. Pull out the front door trim board in the direction indicated by the arrow shown in the illustration.

    4. Raise the front door trim board and remove the front door trim board together with the front door inner glass weatherstrip.

    5. for Driver Side with Memory:


      1. Disconnect the connector.

    6. A01CBN8

      Disengage the 2 claws and disconnect the front door inside handle sub-assembly.

  12. Click here

    REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A01CFBK

      Disconnect the front door lock remote control cable and front door inside locking cable, and remove the front door inside handle sub-assembly.

  13. Click here

    REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side)


    1. A01CCK8

      Disconnect the 2 connectors.

    2. Remove the 2 screws and the outer mirror control ECU assembly.

  14. Click here

    REMOVE DOOR TRIM BRACKET


    1. A01CCZL

      Disengage the clamp.

    2. Remove the 2 screws and door trim bracket.

  15. Click here

    REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01CFX4

      Disconnect each connector and the 7 clamps.

    2. A01CAM6

      Remove the front door service hole cover.

      Tip:

      Remove the remaining butyl tape on the door.

  16. Click here

    REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY


    1. A01CCXV

      Remove the bolt and front door rear lower frame sub-assembly.

  17. Click here

    REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)


    1. A01CC2C

      Using a screwdriver, disengage the 2 claws and remove the front door outside handle cover.

  18. Click here

    REMOVE FRONT DOOR LOCK ASSEMBLY


    1. A01CG7M

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Slide the front door lock assembly downward, and remove the front door lock assembly and cables as a unit.

    3. Remove the door lock wiring harness seal from the front door lock assembly.

    4. A01CEPB

      Remove the front door lock remote control cable assembly.

    5. A01CATZ

      Using a screwdriver, disengage the 3 claws.

      Tip:

      Tape the screwdriver tip before use.

    6. A01CETQ

      Remove the front door inside locking cable assembly.