REVOLUTION SENSOR REMOVAL


  1. REMOVE RADIATOR COVER SUB-ASSEMBLY


    1. A01CDEV

      Using a clip remover, remove the 4 clips and radiator cover sub-assembly.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE WINDSHIELD WIPER MOTOR AND LINK

    Click here.

  4. DISCONNECT BRAKE MASTER CYLINDER RESERVOIR WITH BRACKET


    1. A01CBAK

      Remove the 2 nuts and separate the brake master cylinder reservoir with bracket from the outer cowl top panel.

  5. REMOVE OUTER COWL TOP PANEL


    1. A01CED5

      Apply protective tape as shown in the illustration.

      Text in Illustration
      A01CC81 Protective Tape
    2. A01CCFB

      Disconnect the 2 clamps from the outer cowl top panel.

    3. Remove the 8 bolts.

    4. A01CDT7

      Remove the outer cowl top panel as shown in the illustration.

  6. REMOVE BATTERY


    1. Disconnect the positive (+) cable from the positive (+) battery terminal.

    2. A01CDEA

      Disconnect the 2 wire clamps.

    3. Loosen the nut, and remove the bolt and battery clamp.

    4. Remove the battery and battery insulator.

  7. REMOVE BATTERY TRAY


    1. Remove the battery tray.

  8. REMOVE AIR CLEANER CAP AND HOSE


    1. A01CEOK

      Disconnect the No. 1 vacuum switching valve connector and wire harness clamp.

    2. Disconnect the fuel vapor feed hose from the No. 1 vacuum switching valve assembly.

    3. A01CCLR

      Disconnect the purge line hose from the No. 1 vacuum switching valve assembly and air cleaner hose.

    4. A01CFO3

      Disconnect the ventilation hose.

    5. A01CD15

      Disconnect the mass air flow meter connector.

    6. Disconnect the 2 wire harness clamps.

    7. A01CBRKE01
      Text in Illustration
      *1 No. 1 Air Cleaner Hose Clamp

      Lock the No. 1 air cleaner hose clamp as shown in the illustration, and disconnect the No. 1 air cleaner hose from the throttle body.

    8. A01CDPJ

      Disconnect the 2 clamps and remove the air cleaner cap with hose.

  9. REMOVE AIR CLEANER CASE


    1. Remove the air cleaner filter element.

    2. A01CD2Y

      Disconnect the wire clamp.

    3. Remove the 3 bolts and air cleaner case.

  10. REMOVE TRANSMISSION REVOLUTION SENSOR (NT)

    A01CCJUE01

    1. Disconnect the transmission revolution sensor connector.

    2. Remove the bolt and transmission revolution sensor.

    3. Remove the O-ring from the transmission revolution sensor.

  11. REMOVE TRANSMISSION REVOLUTION SENSOR (NIN)

    A01CDH6E01

    1. Disconnect the transmission revolution sensor connector.

    2. Remove the bolt and transmission revolution sensor.

    3. Remove the O-ring from the transmission revolution sensor.

  12. REMOVE TRANSMISSION REVOLUTION SENSOR (NOUT)


    1. A01CB1V

      Disconnect the wire harness clamp and throttle body connector.

    2. Disconnect the fuel pipe from the fuel pipe support bracket.

    3. A01CE53

      Remove the bolt and fuel pipe support bracket.

    4. A01CGHV

      Remove the 3 bolts and throttle body assembly.

      Tech Tips

      Use wire or an equivalent tool to hang the throttle body assembly while keeping the water by-pass hoses connected.

    5. A01CD9V

      Remove the gasket from the intake manifold.

    6. A01CAPT

      Remove the bolt and disconnect the engine wire.

    7. Disconnect the clamp from the wire harness clamp bracket.

    8. A01CCKOE01

      Disconnect the transmission revolution sensor connector.

    9. Remove the bolt and transmission revolution sensor.

    10. Remove the O-ring from the transmission revolution sensor.