SPEED SENSOR INSTALLATION


  1. INSTALL SPEED SENSOR (NC)


    1. Coat a new O-ring with ATF and install it to the speed sensor.

    2. Install the speed sensor with the bolt.

      Torque:
      11 N*m  { 115 kgf*cm, 8 ft.*lbf }

    3. Connect the speed sensor connector.

  2. INSTALL SPEED SENSOR (NT)


    1. Coat a new O-ring with ATF and install it to the speed sensor.

    2. Install the speed sensor with the bolt.

      Torque:
      11 N*m  { 115 kgf*cm, 8 ft.*lbf }

    3. Connect the speed sensor connector.

  3. INSTALL BATTERY CARRIER SUPPORT


    1. Install the battery carrier support with the 2 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  4. INSTALL BATTERY CARRIER


    1. Install the battery carrier with the 4 bolts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    2. Attach the 2 wire harness clamps.

  5. INSTALL BATTERY TRAY

  6. INSTALL NO. 2 AIR CLEANER INLET


    1. Install the No. 2 air cleaner inlet with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  7. INSTALL AIR CLEANER CASE


    1. Install the air cleaner case with the 3 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Install the engine wire clamp to the air cleaner case.

    3. Install the air cleaner filter element.

  8. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH HOSE


    1. A01CDPJ

      Install the air cleaner cap sub-assembly with hose and lock the 2 clamps.

    2. A01CEYSE01
      Text in Illustration
      *1 No. 1 air cleaner hose clamp
      *2 Groove
      *3 Tab
      *4 95°

      Connect the No. 1 air cleaner hose to the throttle body and release the lock of the No. 1 air cleaner hose clamp.

      Note


      • Align the groove of the air cleaner hose with the tab of the throttle body and install the hose.

      • Make sure that the tab of the No. 1 air cleaner hose clamp stays within the range shown by *4

    3. A01CD15

      Connect the 2 wire harness clamps and the mass air flow meter connector.

    4. A01CFO3

      Connect the ventilation hose.

    5. A01CCLR

      Connect the purge line hose to the No. 1 vacuum switching valve assembly and air cleaner hose.

    6. A01CEOK

      Connect the fuel vapor feed hose to the No. 1 vacuum switching valve assembly.

    7. Connect the wire harness clamp and No. 1 vacuum switching valve connector.

  9. INSTALL BATTERY


    1. Install the battery and battery insulator.

    2. Install the battery clamp with the bolt and nut.

      Torque:
      Bolt
      46 N*m  { 469 kgf*cm, 34 ft.*lbf }
      Nut
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

    3. Connect the 2 wire harness clamps.

    4. Connect the positive (+) cable to the positive (+) battery terminal.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. INSTALL RADIATOR COVER SUB-ASSEMBLY


    1. Install the radiator cover sub-assembly with the 4 clips.