ENGINE SWITCH INSTALLATION


  1. INSTALL ENGINE SWITCH (for RHD)


    1. A01CCY3E01

      Attach the 2 claws to install the engine switch.

  2. INSTALL NO. 1 SWITCH HOLE BASE (for RHD)


    1. Connect each connector.

    2. Engage the 6 claws and 3 guides to install the No. 1 switch hole base.

      A01CFWGE01

  3. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for RHD)


    1. Connect the connector.

    2. A01CDHT

      Engage the 4 claws to install the No. 1 instrument cluster finish panel garnish.

  4. INSTALL CENTER FLOOR CARPET COVER RH (for RHD)


    1. A01CFS0

      Engage the 4 claws.

    2. A01CDKB

      Install the center floor carpet cover RH with the 2 clips.

  5. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for RHD)


    1. A01CAYP

      Engage the 3 guides and 14 claws.

      Tech Tips

      Make sure that all claws around the entire circumference of the driver side knee airbag assembly are fully engaged.

      Note

      Make sure that the claws are fully engaged.

    2. A01CCKN

      Install the lower instrument panel finish panel with the 3 screws <B>.

    3. A01CC11

      Engage the 3 claws and the fuel lid lock control cable assembly.

    4. A01CC18

      Engage the 3 claws and the hood lock control cable assembly.

  6. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)


    1. A01CE9Q

      Engage the 2 claws and DLC3.

    2. Engage the clamp.

    3. Connect the connector.

    4. A01CFFK

      Engage the 2 claws and 2 guides.

      Note

      Make sure that the claws are fully engaged.

    5. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <B>.

  7. INSTALL COWL SIDE TRIM BOARD RH (for RHD)


    1. A01CFL6

      Engage the 2 guides, claw and clip to install the cowl side trim board RH.

    2. Install the clip(A).

  8. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL (for RHD)


    1. A01CEO2

      Engage the 11 claws and 2 guides to install the No. 1 instrument cluster finish panel.

    2. A01CDZ6E01

      Remove the protective tape from the steering column cover.

  9. INSTALL ENGINE SWITCH (for LHD)


    1. Connect the connector.

    2. A01CF4CE01

      Attach the 2 claws to install the engine switch.

  10. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for LHD)


    1. Connect the connector.

    2. A01CEYM

      Engage the 4 claws to install the air conditioning control assembly.

  11. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD)


    1. A01CFEQ

      Engage the 8 claws to install the No. 2 instrument cluster finish panel garnish.

      Note

      Make sure that the claws are fully engaged.

  12. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for LHD)


    1. Connect the connector.

    2. A01CBOAE01

      Engage the 23 claws to install the center instrument cluster finish panel sub-assembly.

      Note


      • When installing the center instrument cluster finish panel sub-assembly, make sure to press the upper middle part firmly.

      • Make sure that the claws are fully engaged.

    3. Remove the applied protective tape.

    4. Move the shift lever to P.

  13. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (for LHD)


    1. A01CG2C

      Engage the 15 claws.

      Tech Tips

      Before engaging the 15 claws, make sure that the claws are positioned correctly.

      Note

      Make sure that the claws are fully engaged.

    2. Install the instrument cluster finish panel assembly with the bolt <C>.

  14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for LHD)


    1. A01CGCS

      Turn the shift lever knob clockwise to install the shift lever knob sub-assembly.

  15. INSTALL INSTRUMENT PANEL BOX ASSEMBLY (for LHD)


    1. A01CEC3E01

      With the instrument panel box assembly opened approximately 60° from its closed position, engage the 2 hinges horizontally.

      Note

      Engaging the hinges from the top will deform the hinges. Be sure to install the instrument panel box assembly horizontally.

    2. A01CE1FE01

      Install the damper clip.

    3. Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the instrument panel box assembly.

  16. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (for LHD)


    1. A01CDTKE01

      With the glove compartment door assembly opened approximately 55° from its closed position, engage the 2 hinges horizontally.

      Note

      Engaging the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.

    2. A01CDIJE01

      Slightly bend stoppers (A) and (B) in the directions indicated by the arrows in the illustration and engage the stoppers to install the glove compartment door assembly.

    3. Engage the claw and connect the glove compartment door stopper.

  17. INSTALL CENTER FLOOR CARPET COVER LH (for LHD)


    1. A01CF5Y

      Engage the 4 claws.

    2. A01CG2A

      Install the center floor carpet cover LH with the clip.

  18. INSTALL CENTER FLOOR CARPET COVER RH (for LHD)


    1. A01CB02

      Engage the 5 claws.

    2. A01CBO2

      Install the center floor carpet cover RH with the clip.

  19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (for LHD)


    1. A01CE7K

      Engage the 3 guides, 13 claws and clip.

      Tech Tips

      Make sure that all claws around the entire circumference of the driver side knee airbag assembly are fully engaged.

      Note

      Make sure that the claws are fully engaged.

    2. A01CCWL

      Install the lower instrument panel finish panel with the 3 screws <B>.

    3. A01CGDM

      Connect the fuel filler opening lid lock sub-assembly to the fuel lid lock open lever sub-assembly.

    4. A01CCXK

      Engage the 3 claws and the fuel lid lock control cable assembly.

    5. A01CF0E

      Engage the 3 claws and the hood lock control cable assembly.

  20. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)


    1. Engage the clamp.

    2. Connect each connector.

    3. A01CCYO

      Engage the 2 claws and guide.

      Note

      Make sure that the claws are fully engaged.

    4. Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <B>.

  21. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL (for LHD)


    1. A01CEO2

      Engage the 11 claws and 2 guides to install the No. 1 instrument cluster finish panel.

    2. A01CDZ6E01

      Remove the protective tape from the steering column cover.

  22. INSTALL COWL SIDE TRIM BOARD LH (for LHD)


    1. A01CCIK

      Engage the 2 guides, claw and clip to install the cowl side trim board LH.

    2. Install the clip(A).

  23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


    1. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.