Click here

REAR DOOR WINDOW FRAME MOULDING REMOVAL

Click here
Click here Click here
Tip:
  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When removing window frame moulding, heat the vehicle body and window frame moulding using a heat light.

Standard Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Window Frame Moulding 20 to 30°C (68 to 86°F)
Note:

Do not heat the vehicle body and window frame moulding excessively.

Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE REAR DOOR INSIDE HANDLE BEZEL LH


    1. A015B1YE01

      Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

      Tip:

      Tape the screwdriver tip before use.

      Table 1. Text in Illustration
      *1 Protective Tape
  4. Click here

    REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH


    1. A015ALM

      Using a moulding remover, detach the 7 claws.

    2. Disconnect the connector and remove the armrest base panel.

  5. Click here

    REMOVE ASSIST GRIP COVER LH


    1. A015D94

      Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.

  6. Click here

    REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A0155STE01

      Remove the 3 screws.

    2. Remove the 9 clips.

    3. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

      Tip:

      Make sure that the pin labeled A in the illustration is detached from the door panel.

    4. Disconnect the connector and remove the rear door trim board sub-assembly LH.

    5. A0159D6

      Disconnect the 2 cables from the rear door inside handle sub-assembly LH.

  7. Click here

    REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. A015864

      Detach the 4 clips and remove the rear inner door glass weatherstrip LH from the rear door trim board sub-assembly LH.

      Note:
      • Squeeze the metal clip to remove it.

      • The metal clip may be deformed if it is forcibly pulled.

  8. Click here

    REMOVE REAR DOOR SERVICE HOLE COVER LH


    1. A0158QNE01

      Using a clip remover, detach the 6 clamps.

    2. Remove the bolt and disconnect the 2 connectors.

    3. Remove the rear door service hole cover LH.

      Tip:

      Remove the remaining tape on the door.

  9. Click here

    REMOVE REAR DOOR GLASS RUN LH


    1. A015C0T

      Remove the rear door glass run LH from the window frame.

  10. Click here

    REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH


    1. A0159WG

      Remove the 2 bolts.

    2. Remove the screw and rear door rear lower window frame sub-assembly LH.

  11. Click here

    REMOVE REAR DOOR QUARTER WINDOW GLASS LH


    1. A0157CH

      Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.

  12. Click here

    REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH


    1. A0158QI

      Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.

      Note:

      Do not damage the door glass.

  13. Click here

    REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH


    1. Put protective tape around the belt moulding.

    2. A0158XC

      Detach the claw and remove the belt moulding.

  14. Click here

    REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH


    1. Put protective tape around the window frame moulding.

    2. Detach the clip and remove the double-sided tape to remove the window frame moulding.