FRONT DOOR WINDOW FRAME MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • When installing the window frame moulding, heat the vehicle body and window frame moulding using a heat light.

Standard Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Window Frame Moulding 20 to 30°C (68 to 86°F)

Note

Do not heat the vehicle body and window frame moulding excessively.


  1. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH


    1. Clean the vehicle body surface.


      1. Using a heat light, heat the vehicle body surface.

      2. Remove the double-sided tape from the vehicle body surface.

      3. Wipe off any tape adhesive residue with cleaner.

    2. Install a new window frame moulding.


      1. Using a heat light, heat a new window frame moulding and the vehicle body surface.

      2. Remove the peeling paper from the face of the window frame moulding.

        Tech Tips

        After removing the peeling paper, keep the exposed adhesive free from foreign matter.

      3. A01597ZE02

        Attach the clip and double-sided tape to install the window frame moulding.

        Tech Tips

        Press the window frame moulding firmly to install it.

  2. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

    A0158BK

    1. Attach the claw to install the belt moulding.

  3. INSTALL FRONT DOOR GLASS RUN LH


    1. Install the front door glass run LH.

  4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. A01577I

      Insert the front door glass sub-assembly LH into the door panel along the glass run as indicated by the arrows in the illustration.

      Note

      Be careful not to damage the glass.

    2. Install the front door glass sub-assembly LH to the front door window regulator sub-assembly LH with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  5. INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH


    1. A0158YW

      Install the front inner door glass weatherstrip LH.

  6. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. A0159DX

      Apply butyl tape to the door.

    2. Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.

      Note


      • When installing the front door service hole cover LH, pull the links and connectors through the front door service hole cover LH.

      • There should be no wrinkles or folds after attaching the front door service hole cover LH.

      • After attaching the front door service hole cover LH, check the sealing quality.

    3. A015E44E01

      Connect the 2 connectors.

    4. Attach the 9 clamps.

    5. Install the bolt as shown in the illustration.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

  7. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

    A015B6ZE01

    1. Attach the claw and Install the mirror with the 3 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. w/ Power Mirror Control System:


      1. Attach the clamp.

      2. Connect the connector labeled A.

  8. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A015BOB

      Connect the connector.

    2. Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH to the front door inside handle sub-assembly LH.

    3. A015803

      Attach the 4 claws and 13 clips to install the front door trim board sub-assembly LH.

    4. Install the 3 screws.

  9. INSTALL DOOR ASSIST GRIP COVER LH


    1. Attach the 8 claws to install the door assist grip cover LH to the front door trim board sub-assembly LH.

  10. INSTALL FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. A015C09

      Attach the 5 claws to install the armrest base panel.

  11. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH


    1. Install the front door inside handle bezel LH to the trim board with the 7 screws.

  12. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH


    1. Attach the clip and claw, and install the front door lower frame bracket garnish LH.

  13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.