WINCH UNIT INSTALLATION


  1. INSTALL WINCH ASSEMBLY


    1. A015AW1

      Using a crane or equivalent, install the winch assembly.

      CAUTION:

      Be careful as the winch assembly is very heavy.

    2. A015AJX

      Connect the wire with the nut.

      Torque:
      9.3 N*m  { 95 kgf*cm, 83 in.*lbf }

    3. Connect the connector.

    4. A0156EE

      Move the cover in the direction indicated by the arrow shown in the illustration and attach the 2 claws.

    5. A015B22E01

      Install the mounting bracket with the 9 bolts.

      Torque:
      for bolt A
      33 N*m  { 336 kgf*cm, 24 ft.*lbf }
      for bolt B
      19 N*m  { 194 kgf*cm, 15 ft.*lbf }

  2. INSTALL WINCH CONTROL WIRE


    1. A015AQC

      Install the winch control wire with the 2 nuts.

      Torque:
      5 N*m  { 51 kgf*cm, 45 in.*lbf }

  3. INSTALL TRANSMISSION OIL COOLER AIR DUCT (w/ Oil Cooler)


    1. Install the oil cooler air duct with the 4 bolts.

      Torque:
      4.9 N*m  { 50 kgf*cm, 43 in.*lbf }

  4. INSTALL RADIATOR SIDE DEFLECTOR RH (w/o Oil Cooler)


    1. Install the deflector with the 4 clips.

  5. INSTALL RADIATOR SIDE DEFLECTOR LH


    1. Install the side deflector with the 4 clips.

  6. INSTALL FRONT UPPER CENTER BUMPER RETAINER


    1. Install the front upper center bumper retainer with the 3 bolts.

  7. INSTALL HEADLIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL HEADLIGHT ASSEMBLY LH


    1. for Halogen Headlight:

      Click here

    2. for HID Headlight:

      Click here

  9. INSTALL FRONT BUMPER EXTENSION RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. INSTALL FRONT BUMPER EXTENSION LH


    1. Install the front bumper extension LH with the 3 bolts.

  11. INSTALL FRONT BUMPER COVER


    1. w/ Fog Light:

      Connect the No. 4 engine room wire connector.

    2. Connect the winch control wire connector and attach the 10 claws to install the front bumper cover.

    3. Install the 3 clips, 4 screws and 4 bolts.

    4. Using a T30 "TORX" socket, install the 6 screws.

  12. INSTALL RADIATOR GRILLE ASSEMBLY


    1. w/ Wide View Front Monitor System:


      1. Connect the connector.

    2. Attach the 2 clips and 8 claws to install the radiator grille assembly.

    3. Install the 3 screws.

  13. INSTALL FRONT BUMPER WINCH COVER SUB-ASSEMBLY


    1. Attach the 3 guides.

    2. Attach the 2 claws and front bumper winch cover sub-assembly.

  14. INSTALL UPPER RADIATOR SUPPORT SEAL

    Click here

  15. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. Push in the clip to install the front fender splash shield sub-assembly RH.

    2. Install the 3 bolts and 2 screws.

  16. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. Push in the clip to install the front fender splash shield sub-assembly LH.

    2. Install the 3 bolts and screw.

  17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.