FRONT DOOR BELT MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

    A0158BK

    1. Attach the claw to install the belt moulding.

  2. INSTALL FRONT DOOR GLASS RUN LH


    1. Install the front door glass run LH.

  3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. A01577I

      Insert the front door glass sub-assembly LH into the door panel along the glass run as indicated by the arrows in the illustration.

      Note

      Be careful not to damage the glass.

    2. Install the front door glass sub-assembly LH to the front door window regulator sub-assembly LH with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  4. INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH


    1. A0158YW

      Install the front inner door glass weatherstrip LH.

  5. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. A0159DX

      Apply butyl tape to the door.

    2. Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.

      Note


      • When installing the front door service hole cover LH, pull the links and connectors through the front door service hole cover LH.

      • There should be no wrinkles or folds after attaching the front door service hole cover LH.

      • After attaching the front door service hole cover LH, check the sealing quality.

    3. A015E44E01

      Connect the 2 connectors.

    4. Attach the 9 clamps.

    5. Install the bolt as shown in the illustration.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

  6. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

    A015B6ZE01

    1. Attach the claw and Install the mirror with the 3 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. w/ Power Mirror Control System:


      1. Attach the clamp.

      2. Connect the connector labeled A.

  7. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A015BOB

      Connect the connector.

    2. Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH to the front door inside handle sub-assembly LH.

    3. A015803

      Attach the 4 claws and 13 clips to install the front door trim board sub-assembly LH.

    4. Install the 3 screws.

  8. INSTALL DOOR ASSIST GRIP COVER LH


    1. Attach the 8 claws to install the door assist grip cover LH to the front door trim board sub-assembly LH.

  9. INSTALL FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH


    1. Connect the connector.

    2. A015C09

      Attach the 5 claws to install the armrest base panel.

  10. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH


    1. A015BHG

      Attach the 4 claws to install the front door inside handle bezel LH.

  11. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH


    1. Attach the clip and claw, and install the front door lower frame bracket garnish LH.

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.