Click here

FUEL LID LOCK CONTROL CABLE ASSEMBLY (for RHD) REMOVAL

Click here
Click here Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


    1. Remove the tonneau cover.

  4. Click here

    REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)


    1. Place protective tape as shown in the illustration.

      Table 1. Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, detach the 6 claws and remove the instrument side panel.

  5. Click here

    REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)


    1. Place protective tape as shown in the illustration.

      Table 2. Text in Illustration
      *1 Protective Tape

    2. Using a moulding remover, detach the 6 claws.

    3. Disconnect the connector and remove the instrument side panel.

  6. Click here

    REMOVE COWL SIDE TRIM BOARD RH


    1. Remove the cap nut.

    2. Detach the 2 clips and remove the cowl side trim board.

  7. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedures described for the LH side.

  8. Click here

    REMOVE REAR STEP COVER

    Tip:

    Use the same procedure to remove the step cover on the other side.


    1. Detach the 2 claws and remove the step cover.

  9. Click here

    REMOVE REAR DOOR SCUFF PLATE RH

    Tip:

    Use the same procedures described for the LH side.

  10. Click here

    REMOVE REAR FLOOR MAT REAR SUPPORT PLATE


    1. Detach the 6 clips and remove the support plate.

  11. Click here

    REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)

    Tip:

    Use the same procedure to remove the tonneau cover holder cap on the other side.


    1. Detach the 2 claws and remove the tonneau cover holder cap.

  12. Click here

    REMOVE REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat)

    Tip:

    Use the same procedures described for the rear No. 2 seat cover bezel.

  13. Click here

    REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH

    Tip:

    When removing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.


    1. A0157CJ

      Detach the 3 claws and remove the cover.

    2. A015CPR

      Remove the bolt and rear No. 1 seat belt anchor.

    3. A015DRR

      w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Detach the 3 claws and remove the cover.

      2. A015C42

        Remove the bolt and rear No. 2 seat belt anchor.

    4. w/ Rear No. 2 Seat, except Face to Face Seat Type:


      1. Remove the clip and bolt.

      2. Detach the 16 clips and 2 claws.

      3. w/o Rear Air Conditioning System:

        Disconnect the rear seat lock control lever cable and then remove the quarter trim panel.

      4. A0156CN

        w/ Rear Air Conditioning System:

        Disconnect the thermistor connector and rear seat lock control lever cable, and then remove the quarter trim panel.

    5. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:


      1. Remove the clip.

      2. A0157MJ

        Detach the 16 clips and 2 claws, and remove the quarter trim panel.

    6. w/ Tonneau Cover:


      1. Remove the screw and clip.

      2. A0158OA

        Detach the 16 clips and 2 claws, and remove the quarter trim panel.

  14. Click here

    REMOVE FUEL FILLER OPENING LID LOCK RETAINER


    1. Turn the cable counterclockwise and remove the cable from the retainer.

    2. A0158N6

      Turn the lock retainer counterclockwise and remove the lock retainer.

  15. Click here

    REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A015ABU

      Detach the 2 claws.

    2. Disconnect the fuel lid lock control cable and remove the fuel lid lock open lever.

  16. Click here

    REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY


    1. A015AWD

      Using a screwdriver, disconnect the clamps shown in the illustration.

      Tip:

      Tape the screwdriver tip before use.

    2. Remove the lock control cable.