Click here

POWER WINDOW REGULATOR MOTOR (for Rear Door) REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE REAR DOOR INSIDE HANDLE BEZEL


    1. A015B1YE01

      Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

      Tip:

      Tape the screwdriver tip before use.

      Table 1. Text in Illustration
      *1 Protective Tape
  4. Click here

    REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY


    1. A015ALM

      Using a moulding remover, detach the 7 claws.

    2. Disconnect the connector and remove the armrest base panel.

  5. Click here

    REMOVE ASSIST GRIP COVER


    1. A015D94

      Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.

  6. Click here

    REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A0155STE01

      Remove the 3 screws.

    2. Remove the 9 clips.

    3. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

      Tip:

      Make sure that the pin labeled A in the illustration is detached from the door panel.

    4. Disconnect the connector and remove the rear door trim board sub-assembly LH.

    5. A0159D6

      Disconnect the 2 cables from the rear door inside handle sub-assembly LH.

  7. Click here

    REMOVE REAR INNER DOOR GLASS WEATHERSTRIP


    1. A015864

      Detach the 4 clips and remove the rear inner door glass weatherstrip LH from the rear door trim board sub-assembly LH.

      Note:

      • Squeeze the metal clip to remove it.

      • The metal clip may be deformed if it is forcibly pulled.

  8. Click here

    REMOVE REAR SPEAKER SET (w/ Rear Speaker)


    1. A0155P1

      Disconnect the speaker connector.

    2. Remove the 3 screws.

    3. Detach the claw and remove the speaker.

      Note:

      Do not touch the cone part of the speaker.

  9. Click here

    REMOVE REAR DOOR SERVICE HOLE COVER


    1. A0158QNE01

      Using a clip remover, detach the 6 clamps.

    2. Remove the bolt and disconnect the 2 connectors.

    3. Remove the rear door service hole cover LH.

      Tip:

      Remove the remaining tape on the door.

  10. Click here

    REMOVE REAR DOOR GLASS RUN


    1. A015C0T

      Remove the rear door glass run LH from the window frame.

  11. Click here

    REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A0159WG

      Remove the 2 bolts.

    2. Remove the screw and rear door rear lower window frame sub-assembly LH.

  12. Click here

    REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A0158VK

      Install the rear door quarter window glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.

  13. Click here

    REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A01572Z

      Slide the rear door glass sub-assembly LH as shown in the illustration to install it.

  14. Click here

    REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


    1. A015C6NE05

      Loosen the temporary bolt.

      Note:

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator sub-assembly LH may fall and cause damage.

      Table 2. Text in Illustration
      *1 Temporary Bolt

    2. Remove the 3 bolts and rear door window regulator sub-assembly LH.

      Note:

      Be careful when removing the bolts as the motor may fall and become damaged.

    3. Remove the temporary bolt from the rear door window regulator sub-assembly LH.

  15. Click here

    REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A0155OZE01

      Using a T25 "TORX" driver, remove the 3 screws and motor.

      Note:

      Be careful when removing the screws as the motor may fall and become damaged.

      Table 3. Text in Illustration
      *A for Models with Jam Protection Function on 4 Windows
      *B for Models with Jam Protection Function on Driver Door Window Only