STEERING WHEEL INSTALLATION


  1. INSTALL STEERING WHEEL BOSS LOWER COVER


    1. A0158JJ

      Attach the 4 claws and 2 screws and install the steering wheel boss lower cover.

  2. INSTALL STEERING SHAKE DAMPER


    1. A015BC2

      Install the 2 screws to steering shake damper.

  3. INSTALL STEERING PAD COVER LH (w/o Steering Pad Switch)


    1. A01558CE01

      Install the screw and 4 guide pins, install the steering pad cover LH.

  4. INSTALL STEERING PAD COVER RH (w/o Steering Pad Switch)

    Tech Tips

    Use the same procedures described for the LH side.

  5. INSTALL STEERING WHEEL HEATER CONTROL ASSEMBLY (w/ Steering Heater)


    1. Install the steering wheel heater control assembly to the lower steering wheel boss cover with the 2 screws.

    2. Attach the connector clamp.

    3. Connect the 2 connectors.

  6. ADJUST SPIRAL CABLE


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the battery negative (-) terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A015B8I

      Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

      CAUTION:

      Do not turn the spiral cable with steering sensor by the airbag wire harness.

    4. A015BZRE01

      Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

      CAUTION:

      Do not turn the spiral cable with spiral sensor by the airbag wire harness.

      Tech Tips

      The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.

  7. INSTALL STEERING WHEEL ASSEMBLY


    1. A01571ZE02
      Text in Illustration
      *a Matchmark

      Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  8. INSTALL CRUISE CONTROL MAIN SWITCH (w/ Cruise Control System)


    1. A015C2W

      Install the switch.

    2. A0157YS

      Install the 2 screws.

    3. A015A32

      Connect the connector and clamp.

  9. INSTALL STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)


    1. A015A86

      Attach the 4 claws to install the steering pad switch.

    2. Install the 2 screws.

    3. Connect the connector.

  10. INSTALL STEERING PAD (w/ Airbag System)


    1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

      Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

    2. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system.

  11. INSTALL STEERING PAD (w/o Airbag System)

    Tech Tips

    Refer to the step "INSTALL STEERING PAD (w/ Airbag System)".

  12. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. A0159MPE01

      Attach the 2 claws to install the cover.

  13. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. A015BV6

      Attach the 2 claws to install the cover.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. CHECK SRS WARNING LIGHT


    1. Check the SRS warning light Click here.