STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) INSTALLATION


  1. CONNECT NO. 2 STEERING INTERMEDIATE SHAFT


    1. A015AR4E03
      Text in Illustration
      *a Matchmark

      Align the part of the dust cover labeled A with the No. 2 steering intermediate shaft, and install the No. 2 steering intermediate shaft assembly to the steering link assembly.

    2. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }

      Note

      Be careful not to damage the dust cover.

  2. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY


    1. A0156H2

      Install the 4 bolts and nut.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

      Note

      Do not fold back the boot part of the steering hole cover or extend it excessively. if it is extended excessively, return it to its original position.

      Tech Tips

      Install the steering intermediate shaft assembly from the inside of the vehicle.

    2. Install the clamp to the steering column hole cover.

  3. CONNECT STEERING ACTUATOR ASSEMBLY


    1. Make sure that the power steering link assembly is centered.

    2. A0156V3E01

      Install the steering actuator assembly.


      1. If installing a new steering actuator assembly:

        Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.

        Note

        Do not pull out the center lock pin.

      2. A01569TE01

        If reinstalling the removed steering actuator assembly:


        1. Slowly turn the spiral case clockwise until it locks.

        2. Turn the spiral case two turns counterclockwise from the lock position.

        3. Align the slit of the sliding yoke with the alignment mark (▲).

        4. Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.

    3. A0158GNE01

      Align the matchmarks on the No. 2 steering intermediate shaft and steering actuator.

      Note


      • Do not fold back the boot part of the steering hole cover or turn it excessively. If it is turned excessively, return it to its original position.

      • Do not turn the actuator body and the spiral case.

      Tech Tips

      Install the steering actuator from the inside of the vehicle.

    4. Install the bolt.

      Torque:
      35 N*m  { 360 kgf*cm, 26 ft.*lbf }
    5. A015A1X

      Using needle nose pliers, lock the clamp to the steering column hole cover to install it.

      Note

      Be careful when performing the operation as the clamp may not lock if the claws of the clamp are deformed.

    6. A015ARU

      Move the lock in the direction of the arrow and connect the steering actuator connector.

      Tech Tips

      When a new actuator is installed, remove the center lock pin.

    7. Connect the connector.

  4. INSTALL STEERING COLUMN ASSEMBLY (TILT STEERING GEAR ASSEMBLY WITH MOTOR)


    1. A015CNT

      Install the 4 nuts and steering column.

      Torque:
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }

  5. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY


    1. Attach the 2 claws to install the duct.

    2. Install the clip.

  6. INSTALL WIRE HARNESS PROTECTOR AND WIRE HARNESS


    1. A015C7T

      Attach the 3 claws and install the wiring harness protector and wire harness.

  7. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


    1. A01556EE01

      Connect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Install the driver side knee airbag with the 5 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  8. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    A0158Q7

    1. Attach the 2 claws and connect the DLC3.

    2. Install the lower instrument panel with the 5 bolts.

  9. INSTALL NO. 1 SWITCH HOLE BASE

    A015DE6

    1. Connect the connectors.

    2. Attach the 4 claws to install the No. 1 switch hole base.

  10. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. Connect the connectors.

    2. A0158MF

      for Automatic Air Conditioning System:


      1. Attach the 2 claws to install the room temperature sensor.

    3. A0156SA

      Attach the 2 claws to connect the 2 control cables.

    4. w/ Driver Side Knee Airbag:


      1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

      2. Install the 2 bolts.

        A015CUJ

    5. w/o Driver Side Knee Airbag:


      1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

      2. Install the 2 bolts.

        A015A9A
    6. A015ATT

      Attach the 2 claws to close the hole cover.

  11. INSTALL COWL SIDE TRIM BOARD LH

    A0156SP

    1. Attach the 2 clips to install the cowl side trim board.

    2. Install the cap nut.

  12. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    A015B20

    1. Connect the connectors.

    2. Attach the 3 claws to install the No. 1 instrument panel under cover.

    3. Install the 2 screws.

  13. INSTALL FRONT DOOR SCUFF PLATE LH

    A015BJQ

    1. Attach the 3 claws and 4 clips to install the scuff plate.

    2. Install the screw.

  14. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Multi-information Display)

    A015DOK

    1. Connect the connector.

    2. Attach the 9 claws to install the instrument cluster finish panel.

  15. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Multi-information Display)

    A0158HM

    1. Attach the 9 claws to install the instrument cluster finish panel.

  16. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

      A0156L8E01
      Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System

  17. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    A01555F

    1. Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.

  18. INSTALL INSTRUMENT SIDE PANEL LH

    A0155HU

    1. Attach the 6 claws to install the instrument side panel.

  19. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH


    1. A015D40

      Connect the connectors and 2 clamps.

    2. Attach the 8 claws to install the panel pad.

    3. Install the screw.

    4. Install the clip.

  20. INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION


    1. A015DQB

      Attach the 7 claws to install the panel cushion.

  21. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY


    1. A0157OTE01

      Using pliers, grip the claws of the clamp and install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

    2. A01592M

      Connect the 5 connectors to the turn signal switch with spiral cable.

  22. INSTALL TILT AND TELESCOPIC SWITCH


    1. A0157YI

      Attach the claw to install the switch.

    2. Connect the switch connector.

  23. INSTALL UPPER STEERING COLUMN COVER


    1. A0157F6

      Attach the claw to install the upper steering column cover.

    2. Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.

  24. INSTALL LOWER STEERING COLUMN COVER


    1. A0157LW

      Attach the 2 claws to install the lower steering column cover.

      Note

      Do not damage the tilt and telescopic switch.

    2. Install the 3 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  25. INSTALL STEERING WHEEL ASSEMBLY


    1. A01571ZE02
      Text in Illustration
      *a Matchmark

      Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

    2. Install the steering wheel assembly set nut.

      Torque:
      50 N*m  { 510 kgf*cm, 37 ft.*lbf }

  26. INSTALL STEERING PAD


    1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:

      Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

    2. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system.

  27. INSTALL LOWER NO. 2 STEERING WHEEL COVER


    1. A0159MPE01

      Attach the 2 claws to install the cover.

  28. INSTALL LOWER NO. 3 STEERING WHEEL COVER


    1. A015BV6

      Attach the 2 claws to install the cover.

  29. CHECK FRONT WHEELS FACING STRAIGHT AHEAD

  30. INSTALL FRONT WHEELS

  31. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note


    • Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter Click here.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  32. INSPECT SRS WARNING LIGHT


    1. Inspect the SRS warning light Click here.