STEERING CONTROL ECU (for RHD) INSTALLATION


  1. INSTALL STEERING CONTROL ECU

    A0158EVE01

    1. Install the steering control ECU to the junction block with the 2 bolts.

      Torque:
      for bolt A
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      for bolt B
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  2. INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK


    1. A015C4VE02

      1. Front side:

        Connect the 3 connectors.

    2. Rear side:


      1. Install the steering control ECU with junction block with the bolt and 2 nuts.

        Torque:
        8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

      2. Connect the 2 connectors.

  3. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

    A0158Q7

    1. Attach the 2 claws and connect the DLC3.

    2. Install the lower instrument panel with the 5 bolts.

  4. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


    1. A01556EE01

      Connect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Install the driver side knee airbag with the 5 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  5. INSTALL NO. 1 SWITCH HOLE BASE

    A015DE6

    1. Connect the connectors.

    2. Attach the 4 claws to install the No. 1 switch hole base.

  6. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. Connect the connectors.

    2. A0158MF

      for Automatic Air Conditioning System:


      1. Attach the 2 claws to install the room temperature sensor.

    3. A0156SA

      Attach the 2 claws to connect the 2 control cables.

    4. w/ Driver Side Knee Airbag:


      1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

      2. Install the 2 bolts.

        A015CUJ

    5. w/o Driver Side Knee Airbag:


      1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

      2. Install the 2 bolts.

        A015A9A
    6. A015ATT

      Attach the 2 claws to close the hole cover.

  7. INSTALL COWL SIDE TRIM BOARD RH

    A015D0K

    1. Attach the 2 clips to install the cowl side trim board.

    2. Install the cap nut.

  8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

    A015B20

    1. Connect the connectors.

    2. Attach the 3 claws to install the No. 1 instrument panel under cover.

    3. Install the 2 screws.

  9. INSTALL FRONT DOOR SCUFF PLATE RH (w/ Sliding Roof)

    Tech Tips

    Use the same procedures described for the LH side.

  10. INSTALL FRONT DOOR SCUFF PLATE RH (w/o Sliding Roof)

    Tech Tips

    Use the same procedures described for the LH side.

  11. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

      A0156L8E01
      Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System

  12. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

    A01555F

    1. Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.

  13. INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

    A01569W

    1. Connect the connector.

    2. Attach the 6 claws to install the instrument side panel.

  14. INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

    A015ASI

    1. Attach the 6 claws to install the instrument side panel.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.