Click here

BRAKE PEDAL (for LHD) INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL BRAKE PEDAL SUPPORT ASSEMBLY


    1. A015CY0E01

      Install the brake pedal support assembly with the 4 nuts.

      14 N*m 145 kgf*cm 10 ft.*lbf
    2. A015CI3E01

      Install the brake pedal support reinforcement set bolt.

      16 N*m 163 kgf*cm 12 ft.*lbf

    3. Tighten the hexagon bolt.

      23 N*m 239 kgf*cm 17 ft.*lbf
      Tip:

      Hold the bolt in place and tighten the nut.

  2. Click here

    INSTALL PUSH ROD PIN


    1. Apply a light coat of lithium soap base glycol grease to the inner surface of the hole on the brake pedal lever.

    2. A0157EGE01

      Set the master cylinder push rod clevis in place, insert the push rod pin from the outside of the vehicle and then install a new clip.

  3. Click here

    INSTALL STOP LIGHT SWITCH ASSEMBLY


    1. Install the stop light switch (Click here).

    2. Connect the stop light switch connector.

  4. Click here

    INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY


    1. A01556EE01

      Connect the connector.

      Note:

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Install the driver side knee airbag with the 5 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  5. Click here

    INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. Connect the connectors.

    2. A0158MF

      for Automatic Air Conditioning System:


      1. Attach the 2 claws to install the room temperature sensor.

    3. A0156SA

      Attach the 2 claws to connect the 2 control cables.

    4. w/ Driver Side Knee Airbag:


      1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

      2. A015CUJ

        Install the 2 bolts.

    5. w/o Driver Side Knee Airbag:


      1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

      2. A015A9A

        Install the 2 bolts.

    6. A015ATT

      Attach the 2 claws to close the hole cover.

  6. Click here

    INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connectors.

    2. Attach the 3 claws to install the No. 1 instrument panel under cover.

    3. Install the 2 screws.

  7. Click here

    INSTALL COWL SIDE TRIM BOARD LH


    1. Attach the 2 clips to install the cowl side trim board.

    2. Install the cap nut.

  8. Click here

    INSTALL FRONT DOOR SCUFF PLATE LH


    1. Attach the 7 claws and 4 clips to install the scuff plate.

  9. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  10. Click here

    CHECK BRAKE PEDAL HEIGHT


    1. A01587XE01

      Check the brake pedal height.

      Standard Pedal Height from No. 2 Dash Panel Insulator Pad
      147.1 to 157.1 mm (5.80 to 6.18 in.)
      Note:

      Do not adjust the pedal height. Doing so by changing the push rod length will structurally change the pedal ratio.

      If the pedal height is incorrect, adjust the rod operating adapter length.

    2. A015ANDE01

      Adjust the rod operating adapter length.


      1. Remove the clip and clevis pin.

      2. Loosen the clevis lock nut.

      3. Adjust the rod operating adapter length by turning the pedal push rod clevis.

        Standard Rod Operating Adapter Length "A"
        201.7 to 202.7 mm (7.94 to 7.98 in.)

      4. Tighten the clevis lock nut.

        26 N*m 260 kgf*cm 19 ft.*lbf

      5. Set the master cylinder push rod clevis in place, insert the push rod pin from the outside of the vehicle and then install a new clip.

        If the pedal height is incorrect even if the rod operating adapter is adjusted, check that there is no damage in the brake pedal, brake pedal lever, brake pedal support and dash panel.


        • Even if there is damage, there is no problem if the reserve distance is within the standard value.

        • If necessary, replace any damaged parts.

  11. Click here

    CHECK PEDAL FREE PLAY


    1. A015A4AE01

      Push in the pedal until the beginning of the resistance is felt. Measure the pedal free play.

      Standard Pedal Free Play
      1 to 6 mm (0.0394 to 0.236 in.)
  12. Click here

    CHECK PEDAL RESERVE DISTANCE


    1. A015E2FE01

      Release the parking brake lever. With the engine running, depress the pedal and measure the pedal reserve distance as shown in the illustration.

      Standard Pedal Reserve Distance from No. 2 Dash Panel Insulator Pad at 490 N (50 kgf, 110.2 lbf)
      More than 67 mm (2.64 in.)

      If incorrect, troubleshoot the brake system.