Click here

FRONT ACCELERATION SENSOR INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL ACCELERATION SENSOR (for Driver Side)


    1. A015A33

      Install the sensor with the bolt.

      8.0 N*m 82 kgf*cm 71 in.*lbf

    2. Connect the connector.

  2. Click here

    INSTALL ACCELERATION SENSOR (for Front Passenger Side)


    1. A015AXA

      Install the sensor with the bolt.

      8.0 N*m 82 kgf*cm 71 in.*lbf

    2. Connect the connector.

  3. Click here

    INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK (for LHD)


    1. A0158Z4E01

      Vehicle front side:


      1. Connect the 5 connectors.

    2. Vehicle rear side:


      1. Install the steering control ECU with junction block to the vehicle with the 2 bolts and nut .

        8.0 N*m 82 kgf*cm 71 in.*lbf

      2. Attach the 2 clamps.

      3. Connect the 7 connectors.

  4. Click here

    INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK (for RHD)


    1. A015C4VE01

      Vehicle front side:


      1. Connect the 3 connectors.

    2. Vehicle rear side:


      1. Install the steering control ECU with junction block to the vehicle with the bolt and 2 nuts.

        8.0 N*m 82 kgf*cm 71 in.*lbf

      2. Connect the 2 connectors.

  5. Click here

    INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. Connect the connector.

    2. Attach the 3 claws to install the lower No. 2 instrument panel finish panel.

    3. Install the 4 bolts.

  6. Click here

    INSTALL INSTRUMENT PANEL BOX DOOR KNOB


    1. Attach the 2 claws to install the instrument panel box door knob.

  7. Click here

    INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.

  8. Click here

    INSTALL LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)


    1. Attach the 4 claws to install the lower instrument panel.

    2. Install the 2 bolts.

  9. Click here

    INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)


    1. A015670E01

      Connect the connector.

      Note:

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Attach the 4 claws to install the front passenger side knee airbag.

    3. Install the 4 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  10. Click here

    CLEAN COWL SIDE TRIM BOARD RH


    1. Attach the 2 clips to install the cowl side trim board.

    2. Install the cap nut.

  11. Click here

    INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)


    1. Attach the 4 claws to install the No. 2 instrument panel under cover.

  12. Click here

    INSTALL FRONT DOOR SCUFF PLATE RH

  13. Click here

    INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)


    1. Connect the connector.

    2. Attach the 6 claws to install the instrument side panel.

  14. Click here

    INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)


    1. Attach the 6 claws to install the instrument side panel.

  15. Click here

    INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)


    1. Attach the 2 claws and connect the DLC3.

    2. Install the lower instrument panel with the 5 bolts.

  16. Click here

    INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)


    1. A01556EE01

      Connect the connector.

      Note:

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Install the driver side knee airbag with the 5 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  17. Click here

    INSTALL NO. 1 SWITCH HOLE BASE


    1. Connect the connectors.

    2. Attach the 4 claws to install the No. 1 switch hole base.

  18. Click here

    CLEAN LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. Connect the connectors.

    2. A0158MF

      for Automatic Air Conditioning System:


      1. Attach the 2 claws to install the room temperature sensor.

    3. A0156SA

      Attach the 2 claws to connect the 2 control cables.

    4. w/ Driver Side Knee Airbag:


      1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

      2. A015CUJ

        Install the 2 bolts.

    5. w/o Driver Side Knee Airbag:


      1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

      2. A015A9A

        Install the 2 bolts.

    6. A015ATT

      Attach the 2 claws to close the hole cover.

  19. Click here

    INSTALL COWL SIDE TRIM BOARD LH


    1. Attach the 2 clips to install the cowl side trim board.

    2. Install the cap nut.

  20. Click here

    INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)


    1. Connect the connectors.

    2. Attach the 3 claws to install the No. 1 instrument panel under cover.

    3. Install the 2 screws.

  21. Click here

    INSTALL FRONT DOOR SCUFF PLATE LH

  22. Click here

    INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A0156L8E01

      Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

      Table 1. Text in Illustration
      *A w/ Entry and Start System *B w/o Entry and Start System
  23. Click here

    INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.

  24. Click here

    INSTALL INSTRUMENT SIDE PANEL LH


    1. Attach the 6 claws to install the instrument side panel.

  25. Click here

    INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. Connect the connectors.

    2. Attach the 7 claws to install the lower center instrument cluster finish panel sub-assembly.

  26. Click here

    INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH


    1. Attach the 7 claws to install the lower instrument panel pad sub-assembly.

    2. Install the clip and screw.

  27. Click here

    INSTALL NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION


    1. Attach the 7 claws to install the No. 1 instrument panel finish panel cushion.

  28. Click here

    INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH


    1. Connect the connectors and attach the 2 clamps.

    2. Attach the 8 claws to install the lower instrument panel pad sub-assembly.

    3. Install the clip and screw.

  29. Click here

    INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION


    1. Attach the 7 claws to install the No. 2 instrument panel finish panel cushion.

  30. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  31. Click here

    CHECK SRS WARNING LIGHT


    1. Check the SRS warning light (Click here).