Click here

OIL PUMP INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL WATER INLET PIPE


    1. Apply soapy water to 2 new O-rings and install them to the inlet pipe.

    2. Install the inlet pipe to the No. 1 heat exchanger cover.

  2. Click here

    INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    1. Apply a light coat of engine oil to a new oil pump gasket.

    2. Install the oil pump gasket.

    3. Apply a light coat of engine oil to a new O-ring.

    4. Install the O-ring.

    5. A015CH6E03

      Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

      Table 1. Text in Illustration
      *1 Continuous line area *2 Dashed line area
      *3 Diagonal line area - -
      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      • A015CATE08
        Apply Seal Packing as Follows
        Area Seal Packing Diameter Application Position from Inside Edge of Cover
        Continuous Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.) 2.5 mm (0.0984 in.)
        Dashed Line Area 6.4 mm (0.252 in.) or more, or within OK area shown in illustration 7.0 mm (0.276 in.)
        Diagonal Line Area 3.0 to 4.0 mm (0.118 to 0.157 in.) 5.5 mm (0.217 in.)
        Table 2. Text in Illustration
        *1 Seal Packing Thickness mm (in.)
        *2 Seal Packing Width mm (in.)
        *3 Seal Packing Thickness
        *4 Seal Packing Width
        *5 OK Area
      Note:

      • When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

      • Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

    6. A0156CW

      Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.

    7. A0155BDE04

      Temporarily install the timing chain cover with the 28 bolts and nut.

      Standard Bolt
      Item Length Thread Diameter
      Bolt A 25 mm (0.984 in.) 8 mm (0.315 in.)
      Bolt B 55 mm (2.17 in.) 8 mm (0.315 in.)
      Bolt C 70 mm (2.76 in.) 8 mm (0.315 in.)
      Bolt D 35 mm (1.38 in.) 10 mm (0.394 in.)
      Bolt E 55 mm (2.17 in.) 10 mm (0.394 in.)
      Bolt F 80 mm (3.15 in.) 10 mm (0.394 in.)
      Table 3. Text in Illustration
      *1 Nut
      Note:

      Make sure that there is no oil on the bolt threads.

    8. A015DI7E01

      Tighten the 3 bolts in several steps in the sequence shown in the illustration.

      47 N*m 479 kgf*cm 35 ft.*lbf
    9. A015B96E01

      Temporarily install the fluid coupling bracket with the 4 bolts.

      Standard Bolt
      Item Length Thread Diameter
      Bolt A 70 mm (2.76 in.) 8 mm (0.315 in.)
      Bolt B 80 mm (3.15 in.) 10 mm (0.394 in.)
    10. A01560I

      Temporarily install the belt tensioner with the standard bolt and 6 mm hexagon wrench bolt.

    11. A0155ZRE01

      Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.

      47 N*m 479 kgf*cm 35 ft.*lbf
    12. A015COZE01

      Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the illustration.

      23 N*m 235 kgf*cm 17 ft.*lbf
      Note:

      • Do not start the engine for at least 2 hours after installing.

      • A015564E01

        After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.

  3. Click here

    INSTALL SPARK PLUG TUBE GASKET


    1. A0158WCE07

      Using a cutter knife, cut off the seal part of the removed gasket.

      Table 4. Text in Illustration
      A015DSP Area to cut off
    2. A015BHTE02

      Using the removed gasket and a hammer, tap in a new gasket until it stops.

      Table 5. Text in Illustration
      *1 Removed Gasket
      *2 New Gasket
      Tip:

      If the removed gasket does not fit on the new one, correct the removed one with pliers.

    3. Apply a light coat of MP grease to the lip of the gasket.

    4. Return the 4 ventilation baffle plate claws to the original positions.

  4. Click here

    INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH


    1. Install 5 new gaskets to the camshaft bearing caps (No. 2, No. 3).

    2. Install a new gasket to the cylinder head cover.

      Note:

      Remove any oil from the contact surface.

    3. A01558JE06

      Apply seal packing as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Table 6. Text in Illustration
      A015DIT Seal Packing
      Note:

      • Remove any oil from the contact surface.

      • Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

    4. A0155S9E02

      Install the cylinder head cover and a new seal washer with the 14 bolts in the order shown in the illustration.

      for bolt A
      21 N*m 214 kgf*cm 15 ft.*lbf
      except bolt A
      12 N*m 122 kgf*cm 9 ft.*lbf
      Note:

      Do not start the engine for at least 2 hours after the installation.

  5. Click here

    INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH


    1. Install 5 new gaskets to the camshaft bearing caps. (No. 1, No. 3).

    2. Install a new gasket to the cylinder head cover.

      Note:

      Remove any oil from the contact surface.

    3. A015AGIE06

      Apply seal packing as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Table 7. Text in Illustration
      A015DIT Seal Packing
      Note:

      • Remove any oil from the contact surface.

      • Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

    4. A015BOEE02

      Install the cylinder head cover and a new seal washer with the 14 bolts in the order shown in the illustration.

      for bolt A
      21 N*m 214 kgf*cm 15 ft.*lbf
      except bolt A
      12 N*m 122 kgf*cm 9 ft.*lbf
      Note:

      Do not start the engine for at least 2 hours after the installation.

    5. Install the noise filter to the cylinder head cover with the bolt.

      7.0 N*m 71 kgf*cm 62 in.*lbf
  6. Click here

    INSTALL IGNITION COIL ASSEMBLY


    1. Install the 8 ignition coils with the 8 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  7. Click here

    INSTALL CRANKSHAFT TIMING GEAR KEY


    1. Install the crankshaft timing gear key to the crankshaft.

  8. Click here

    CONNECT WIRE HARNESS CLAMP BRACKET


    1. Connect the bracket to the timing chain cover with the bolt.

      8.0 N*m 82 kgf*cm 71 in.*lbf
  9. Click here

    INSTALL CRANKSHAFT PULLEY


    1. A015B87E06

      Align the pulley set key with the key groove of the pulley, and slide on the pulley.

    2. Using SST, install the pulley set bolt.

      09213-70011
      09330-00021
      300 N*m 3059 kgf*cm 221 ft.*lbf
      Table 8. Text in Illustration
      *a Hold
      A015DIT Turn
  10. Click here

    INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY


    1. Install the idler pulley with the bolt.

      43 N*m 438 kgf*cm 32 ft.*lbf
  11. Click here

    INSTALL WATER PUMP PULLEY


    1. A015B0UE01

      Temporarily install the pulley with the 4 bolts.

    2. Using SST, hold the pulley and tighten the 4 bolts.

      09960-10010 09962-01000 09963-01000
      21 N*m 214 kgf*cm 15 ft.*lbf
  12. Click here

    INSTALL WATER INLET HOUSING


    1. A015A85E04

      Install a new gasket to the timing chain cover.

    2. Install the water inlet with the 3 bolts.

      21 N*m 214 kgf*cm 15 ft.*lbf
      Table 9. Text in Illustration
      *1 Gasket
  13. Click here

    INSTALL NO. 1 ENGINE COVER

  14. Click here

    INSTALL NO. 2 ENGINE COVER

  15. Click here

    INSTALL FRONT WATER BY-PASS JOINT


    1. Install 2 new gaskets and the water by-pass joint with the 4 nuts.

      21 N*m 214 kgf*cm 15 ft.*lbf

    2. Connect the No. 2 water by-pass hose to the water by-pass joint.

  16. Click here

    INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY


    1. Connect the 2 hoses.

    2. Install the water by-pass pipe with the 2 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  17. Click here

    INSTALL NO. 1 WATER BY-PASS HOSE


    1. Install the No. 1 water by-pass hose by connecting the hose to the water inlet housing and front water by-pass joint.

  18. Click here

    INSTALL GENERATOR ASSEMBLY


    1. Install the stud bolt.

      10 N*m 102 kgf*cm 7 ft.*lbf

    2. Install the generator with the 3 bolts and nut.

      43 N*m 438 kgf*cm 32 ft.*lbf

    3. Connect the harness bracket to the generator with the bolt.

      31 N*m 316 kgf*cm 23 ft.*lbf

    4. Connect the generator wire with the nut.

      9.8 N*m 100 kgf*cm 87 in.*lbf

    5. Close the terminal cap.

    6. Connect the generator connector.

  19. Click here

    CONNECT OIL COOLER PIPE ASSEMBLY


    1. Connect the oil cooler pipe with the 2 bolts.

      14 N*m 143 kgf*cm 10 ft.*lbf
  20. Click here

    CONNECT VANE PUMP ASSEMBLY

    Tip:

    Before performing the following procedures, move the spacer until the vane pump can be installed.

    Table 10. Text in Illustration
    *1 Spacer

    1. Connect the vane pump to the timing chain cover with the 2 bolts.

      21 N*m 214 kgf*cm 15 ft.*lbf
  21. Click here

    INSTALL INTAKE MANIFOLD


    1. A015B2SE01

      Place 2 new gaskets on the intake manifold.

      Table 11. Text in Illustration
      *1 Gasket

    2. Place the intake manifold on the cylinder head.

    3. Install and uniformly tighten the 8 bolts and 2 nuts in several steps.

      21 N*m 214 kgf*cm 15 ft.*lbf

    4. Install the wire bracket to the intake manifold with the bolt.

      8.0 N*m 82 kgf*cm 71 in.*lbf

    5. Connect the 3 wire clamps to the 3 wire brackets.

    6. Install the No. 3 engine cover.

    7. Install the No. 1 engine cover sub-assembly.

    8. Connect the purge VSV connector.

    9. Connect the purge line hose to the purge VSV.

    10. Connect the vacuum switching valve connector (for ACIS).

    11. Connect the No. 1 ventilation hose.

    12. Connect the 2 water by-pass hoses.

    13. Connect the throttle body connector.

    14. Connect the ventilation hose to the ventilation pipe of the cylinder head cover LH and RH.

  22. Click here

    INSTALL OIL FILTER BRACKET


    1. Apply a light coat of engine oil to 2 new O-rings.

    2. Install the 2 O-rings to the timing chain cover.

    3. Install the oil filter bracket with the 2 nuts and 2 bolts.

      35 N*m 357 kgf*cm 26 ft.*lbf
  23. Click here

    INSTALL NO. 1 OIL COOLER BRACKET


    1. Connect the ground wire to the cylinder block.

    2. Install the oil cooler bracket with the 2 nuts.

      21 N*m 214 kgf*cm 15 ft.*lbf
  24. Click here

    INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY


    1. Connect the 4 hoses.

    2. Install the water by-pass pipe with the 3 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  25. Click here

    INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY


    1. Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
      A015DZ4E02
      Note:

      Do not allow adhesive to contact the oil hole.

      Table 12. Text in Illustration
      *1 Oil Hole

    2. Install the oil pressure sender gauge.

      15 N*m 153 kgf*cm 11 ft.*lbf
      Note:

      Do not start the engine within 1 hour after installation.

    3. Connect the sender gauge connector.

  26. Click here

    INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Apply a light coat of engine oil to a new O-ring.

    2. Install the O-ring to the guide.

    3. Install the dipstick guide with the bolt.

      10 N*m 102 kgf*cm 7 ft.*lbf

    4. Install the dipstick.

    5. Connect the wire harness clamp.

  27. Click here

    INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, its threads and its O-ring groove.

    2. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

    3. Set a new oil filter element to the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

      Note:

      Do not remove the oil filter bracket clip.

    6. A0159OCE02

      Using SST, tighten the oil filter cap.

      09228-06501
      25 N*m 255 kgf*cm 18 ft.*lbf
      Table 13. Text in Illustration
      *1 Oil Filter Bracket Clip
      Note:

      • When tightening the oil filter cap, do not remove the oil filter bracket clip.

      • Make sure that the oil filter is installed securely as shown in the illustration.

      • Be careful that the O-ring does not get caught between any surrounding parts.

    7. A015BR1E01

      Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

      Table 14. Text in Illustration
      *1 O-Ring
      Note:

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. Install the oil filter drain plug.

      13 N*m 127 kgf*cm 9 ft.*lbf
      Note:

      Be careful that the O-ring does not get caught between any surrounding parts.

    9. Install the No. 2 engine under cover seal with the 2 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
  28. Click here

    CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY


    1. A015BQIE04

      Connect the fuel tube with the 2 bolts.

      10 N*m 102 kgf*cm 7 ft.*lbf
      Table 15. Text in Illustration
      *A LH Side
      *B RH Side
  29. Click here

    CONNECT COOLER COMPRESSOR ASSEMBLY


    1. A0158V3E01

      Install the cooler compressor with the stud bolt.

      10 N*m 102 kgf*cm 7 ft.*lbf

    2. Install the 3 bolts and nut.

      25 N*m 250 kgf*cm 18 ft.*lbf
      Note:

      Tighten the bolts and nut in the order shown in the illustration to install the cooler compressor.

  30. Click here

    CONNECT WATER PIPE AND HOSE SUB-ASSEMBLY


    1. Connect the water pipe and hose to the cylinder head cover with the 2 bolts.

      18 N*m 184 kgf*cm 13 ft.*lbf

    2. Connect the 3 hoses.

  31. Click here

    CONNECT ENGINE WIRE


    1. Connect the 2 clamps and power steering oil pressure switch connector.

    2. Engine Room RH Side:


      1. Connect the 5 clamps.

      2. Connect the throttle position sensor and throttle control motor connector.

      3. Install the ground wire with the 2 bolts.

        8.0 N*m 82 kgf*cm 71 in.*lbf

      4. Connect the noise filter connector.

      5. Connect the 2 VVT sensor connectors.

      6. Connect the injector connector.

      7. Connect the 4 ignition coil connectors.

      8. Connect the 2 camshaft timing oil control valve connectors.

    3. Engine Room LH Side:


      1. Connect the cooler compressor connector.

      2. Connect the 3 clamps.

      3. Connect the camshaft position sensor connector.

      4. Connect the 2 camshaft timing oil control valve connectors.

      5. Connect the engine coolant temperature sensor connector.

      6. Connect the 4 clamps.

      7. Install the ground wire with the 2 bolts.

        8.0 N*m 82 kgf*cm 71 in.*lbf

      8. Connect the noise filter connector.

      9. Connect the 2 VVT sensor connectors.

      10. Connect the 4 ignition coil connectors.

      11. Connect the injector connector.

      12. Connect the 2 connectors and 2 clips to the engine room junction block.

      13. Install the engine room relay block cover.

  32. Click here

    INSTALL RADIATOR ASSEMBLY

    (Click here)

  33. Click here

    INSTALL AIR CLEANER ASSEMBLY


    1. Install the air cleaner with the 3 bolts.

      5.0 N*m 51 kgf*cm 44 in.*lbf
  34. Click here

    INSTALL AIR CLEANER HOSE ASSEMBLY


    1. A015CFTE01

      Install the air cleaner hose so that the protrusion of the air cleaner cap aligns with the groove of the hose as shown in the illustration.

      Table 16. Text in Illustration
      *1 Groove
      *2 Protrusion

    2. Tighten the 2 clamps.

      2.5 N*m 25 kgf*cm 22 in.*lbf

    3. Connect the vacuum hose.

    4. Connect the No. 2 ventilation hose.

  35. Click here

    INSTALL V-BANK COVER SUB-ASSEMBLY


    1. A0157E7E02

      Attach the 2 V-bank cover hooks to the bracket. Then align the 3 V-bank cover grommets with the 3 pins, and press down on the V-bank cover to attach the pins.

      Table 17. Text in Illustration
      *1 Bracket
      *2 Hook
      *3 Pin
      *4 Grommet
  36. Click here

    ADD ENGINE OIL


    1. Add fresh oil and install the oil filler cap.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", API grade SM "energy-conserving", API grade SN "energy-conserving" or ILSAC multigrade engine oil

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil

      15W-40

      20W-50
      Standard Oil Capacity
      Item Specified Condition
      Drain and refill without oil filter change 7.1 liters (7.5 US qts, 6.2 Imp. qts)
      Drain and refill with oil filter change 7.5 liters (7.9 US qts, 6.6 Imp. qts)
      Dry fill 9.3 liters (9.8 US qts, 8.2 Imp. qts)
  37. Click here

    ADD ENGINE COOLANT


    1. Add engine coolant.

      Standard Capacity
      Item Specified Condition
      with rear heater 16.2 liters (17.1 US qts, 14.3 Imp. qts)
      without rear heater 13.4 liters (14.2 US qts, 11.8 Imp. qts)
      Note:

      Do not substitute plain water for engine coolant.

      Tip:

      TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

    2. Slowly pour coolant into the radiator reservoir until it reaches the F line.

    3. Install the reservoir cap.

    4. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

    5. Install the radiator cap.

    6. Start the engine and warm it up until the thermostat opens.

      Tip:

      The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

    7. Maintain the engine speed at 2000 to 2500 rpm.

      Note:

      • Make sure that the radiator reservoir still has some coolant in it.

      • Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.

      • If there is not enough coolant, the engine may burn out or overheat.

      • Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.

      • Run the engine at 2000 rpm until the coolant level has stabilized.

    8. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

      CAUTION:

      • Wear protective gloves.

      • Be careful as the radiator hoses are hot.

      • Keep your hands away from the fan.

    9. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

      CAUTION:

      Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

    10. Check that the coolant level is between the F and L lines.

      If the coolant level is below the L line, repeat all of the procedures above.

      If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L lines.

  38. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  39. Click here

    INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.

  40. Click here

    INSPECT FOR COOLANT LEAK

    CAUTION:

    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Fill the radiator with coolant and attach a radiator cap tester.

    2. Warm up the engine.

    3. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.

      If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.

  41. Click here

    INSPECT ENGINE OIL LEVEL


    1. Warm up the engine. Then stop the engine and wait for 5 minutes.

    2. A0158LWE01

      Check that the engine oil level is between the dipstick low level mark and full level mark.

      Table 18. Text in Illustration
      *a Measuring Surface
      *b Low Level Mark
      *c Full Level Mark

      If the level is low, check for leakage and add oil up to the full level mark.

      Note:

      Do not fill engine oil above the full level mark.

      Tip:

      A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.


      • When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.

      • If low quality oil or oil of an inappropriate viscosity is used.

      • When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.

      • When leaving the idling for a long time, or when driving frequently through heavy traffic.

      When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.

  42. Click here

    INSTALL NO. 2 ENGINE UNDER COVER


    1. Install the No. 2 engine under cover with the 2 bolts.

      29 N*m 296 kgf*cm 21 ft.*lbf
  43. Click here

    INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. Install the No. 1 engine under cover with the 10 bolts.

      29 N*m 296 kgf*cm 21 ft.*lbf
  44. Click here

    INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH


    1. Push in the clip to install the front fender splash shield sub-assembly LH.

    2. Install the 3 bolts and screw.

  45. Click here

    INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH


    1. Push in the clip to install the front fender splash shield sub-assembly RH.

    2. Install the 3 bolts and 2 screws.

  46. Click here

    INSTALL FRONT FENDER APRON SEAL FRONT RH


    1. Install the fender apron seal with the 3 clips.

  47. Click here

    INSTALL FRONT FENDER APRON SEAL LH


    1. Install the fender apron seal with the 3 clips.

  48. Click here

    INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

    (Click here)

  49. Click here

    CONNECT RADIATOR SIDE DEFLECTOR LH


    1. Connect the deflector with the 4 clips.

  50. Click here

    INSTALL TRANSMISSION OIL COOLER AIR DUCT


    1. Install the oil cooler air duct with the 4 bolts.

      4.9 N*m 50 kgf*cm 43 in.*lbf
  51. Click here

    INSTALL FRONT BUMPER COVER

    Tip:

    For the front bumper cover with garnish, use the procedure described below.


    1. A015BCT

      w/ Headlight Cleaner System:

      Connect the headlight cleaner hose.

    2. w/ TOYOTA Parking Assist-sensor System or w/ Fog Light:

      Connect the No. 4 engine room wire connector.

    3. Attach the 10 claws to install the front bumper cover.

    4. Install the 3 clips, 4 screws and 4 bolts.

    5. Using a T30 "TORX" socket, install the 6 screws.

  52. Click here

    INSTALL RADIATOR GRILLE


    1. w/ Wide View Front Monitor System:


      1. Connect the connector.

    2. Attach the 2 clips and 8 claws to install the radiator grille assembly.

    3. Install the 3 screws.

  53. Click here

    INSTALL UPPER RADIATOR SUPPORT SEAL


    1. A015BVKE02

      Install the radiator support seal with the 7 clips.