REAR NO. 1 SEAT OUTER BELT ASSEMBLY INSTALLATION

Tech Tips

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart Click here.

INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
1. Align the anchor plate positioning hole with the claw, and install the anchor plate with the 2 bolts.
  
  Tech Tips
  
  First install the upper bolt, and then install the lower bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
INSTALL REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH
Note

w/ Pretensioner:

When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.
1. Align the claws with the seat belt positioning holes and install the retractor of the seat belt as shown in the illustration.
2. Install the seat belt with the 2 bolts.
  
  Tech Tips
  
  First install bolt A, and then install bolt B.
  
  Torque:
  
  for bolt A
  
  8.5 N*m { 87 kgf*cm, 75 in.*lbf }
  
  for bolt B
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
3. w/ Pretensioner:
  
  Connect the pretensioner connector as shown in the illustration.
4. Install the seat belt shoulder anchor with the nut.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
INSTALL REAR FRONT QUARTER TRIM PANEL ASSEMBLY LH
1. Pass the seat belt anchor through the quarter trim garnish.
2. Attach the clip and 2 guides to install the quarter trim garnish.
3. Install the screw.
INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
Tech Tips

When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.
1. w/o Tonneau Cover:
  1. w/o Rear Air Conditioning System:
    
    Connect the rear seat lock control lever cable.
  2. w/ Rear Air Conditioning System:
    
    Connect the thermistor connector and rear seat lock control lever cable.
  3. Attach the 18 clips and 2 claws to install the quarter trim panel.
  4. Install the clip and bolt.
    
    Torque:
    
    12 N*m { 122 kgf*cm, 9 ft.*lbf }
2. w/ Tonneau Cover:
  1. Attach the 18 clips and 2 claws to install the quarter trim panel.
  2. Install the screw and clip.
3. w/ Rear No. 2 Seat, for LH side:
  1. Install the rear No. 2 seat belt anchor LH with the bolt.
    
    Torque:
    
    42 N*m { 428 kgf*cm, 31 ft.*lbf }
    
    Note
    
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.
4. w/ Rear No. 2 Seat, for RH side:
  1. Install the rear No. 2 seat belt anchor with the bolt.
    
    Torque:
    
    42 N*m { 428 kgf*cm, 31 ft.*lbf }
  2. Attach the 3 claws to install the cover.
5. Install the rear No. 1 seat belt anchor with the bolt.
  
  Torque:
  
  42 N*m { 428 kgf*cm, 31 ft.*lbf }
6. Attach the 3 claws to install the cover.
INSTALL REAR NO. 2 SEAT COVER BEZEL
1. Attach the 6 clips to install the rear No. 2 seat cover bezel.
INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ Tonneau Cover)
Tech Tips

Use the same procedure to install the tonneau cover holder cap on the other side.
1. Attach the 2 claws to install the tonneau cover holder cap.
INSTALL REAR DOOR SCUFF PLATE LH
1. Attach the 3 claws and 4 clips to install the scuff plate.
2. Install the screw.
INSTALL REAR STEP COVER
Tech Tips

Use the same procedure to install the step cover on the other side.
1. Attach the 2 claws to install the step cover.
INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
1. Attach the 6 clips to install the support plate.
INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
1. Install the rear No. 2 seat assembly Click here.
INSTALL TONNEAU COVER ASSEMBLY
1. Install the tonneau cover assembly.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
CHECK SRS WARNING LIGHT
1. Check the SRS warning light Click here.