Click here

FRONT SEAT OUTER BELT ASSEMBLY REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. Click here

    REMOVE FRONT DOOR SCUFF PLATE


    1. Detach the 7 claws and 4 clips, and remove the scuff plate.

  4. Click here

    REMOVE REAR STEP COVER

    Tip:

    Use the same procedure to remove the step cover on the other side.


    1. Detach the 2 claws and remove the step cover.

  5. Click here

    REMOVE REAR DOOR SCUFF PLATE


    1. Remove the screw.

    2. Detach the 3 claws and 4 clips, and remove the scuff plate.

  6. Click here

    REMOVE CENTER PILLAR GARNISH COVER

    Tip:

    • for Manual Seat:

      When removing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. A015AD3

      Detach the 2 clips and 2 guides, and remove the cover.

  7. Click here

    REMOVE CENTER LOWER PILLAR GARNISH

    Tip:

    • for Manual Seat:

      When removing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.

    • for Power Seat:

      When removing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position. After moving the front seat, disconnect the cable from the negative (-) battery terminal.


    1. Remove the bolt and seat belt's anchor.

    2. A0155QQ

      Detach the 2 claws and 7 clips, and remove the center lower pillar garnish.

  8. Click here

    REMOVE REAR ASSIST GRIP ASSEMBLY

    Tip:

    Use the same procedure to remove the rear assist grip on the other side.


    1. Detach the 4 claws and remove the 2 assist grip plugs.

    2. A015DJ8

      Remove the 2 bolts.

    3. Detach the 2 claws and remove the rear assist grip.

  9. Click here

    REMOVE CENTER PILLAR GARNISH


    1. Remove the bolt.

    2. Detach the 2 clips and 2 guides.

    3. Pass the seat belt anchor through the center pillar garnish, and remove the center pillar garnish.

  10. Click here

    REMOVE FRONT SEAT OUTER BELT ASSEMBLY


    1. Remove the nut and shoulder anchor.

    2. A0156OOE01

      Disconnect the pretensioner connector labeled A as shown in the illustration.

    3. Disconnect the tension reducer connector labeled B.

    4. w/ Pre-Crash Safety System:

      Disconnect the pre-crash safety connector labeled C.

    5. A015776

      Remove the bolt and seat belt.

  11. Click here

    REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY


    1. Remove the 2 bolts and adjuster.