Click here

REAR SEATBACK HEATER (for 60/40 Split Seat Type 60 Side) INSTALLATION

Click here
Click here Click here
CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here
  1. Click here

    INSTALL REAR SEATBACK HEATER ASSEMBLY


    1. Set the seatback heater with the name stamp side facing the seatback cover.

    2. A015DFIE01

      Install the seatback heater with new tack pins.

  2. Click here

    INSTALL REAR SEPARATE TYPE SEATBACK COVER


    1. A0157DUE01

      w/ Center Armrest:

      Using hog ring pliers, install the seatback cover with new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    2. A0158DPE01

      w/o Center Armrest:

      Using hog ring pliers, install the seatback cover with new hog rings.

      Note:

      • Be careful not to damage the cover.

      • When installing the hog rings, avoid wrinkling the cover.

    3. A015DQ5

      w/ Rear Seat Side Airbag:

      Connect the seatback cover bracket to the seatback pad.

  3. Click here

    INSTALL SEATBACK COVER WITH PAD


    1. Install the seatback cover with pad.

    2. A015BML

      w/ Center Armrest:

      Pull out the seat belt.

    3. A0158Z6

      w/o Center Armrest:

      Pull out the seat belt.

    4. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seatback.

    5. w/ Seat Heater System:

      Pass the seatback heater wire harness through the hole in the seatback.


      1. A015APP
      2. A015AWWE01

        Connect the seatback heater wire harness and install a new cable tie.

    6. A0159P8

      w/ Rear Seat Side Airbag:

      Install the seatback cover bracket to the seat frame with the cap nut.

      5.5 N*m 56 kgf*cm 49 in.*lbf
      Note:

      After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

    7. A0158CZE01

      w/ Center Armrest:

      Using hog ring pliers, install new hog rings to the seatback frame.

    8. A0159WZE01

      w/o Center Armrest:

      Using hog ring pliers, install new hog rings to the seatback frame.

  4. Click here

    INSTALL REAR SEAT BELT HOLE COVER LH


    1. Attach the 4 claws to install the cover.

    2. Install the screw.

  5. Click here

    INSTALL SHOULDER BELT ANCHOR COVER


    1. Attach the 2 claws to install the cover.

  6. Click here

    INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY


    1. A015C63

      w/ Center Armrest:

      Attach the 4 claws to install the 2 supports.

    2. A01567O

      w/o Center Armrest:

      Attach the 8 claws to install the 4 supports.

  7. Click here

    INSTALL REAR SEAT HEADREST ASSEMBLY

  8. Click here

    INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH


    1. A0158HQ

      w/ Center Armrest:


      1. Push the board down to attach the 2 claws on the bottom.

      2. Attach the 2 claws on the top of the board to install it.

    2. A0159XU

      w/o Center Armrest:


      1. Push the board down to attach the 3 claws on the bottom.

      2. Attach the 3 claws on the top of the board to install it.

  9. Click here

    INSTALL REAR SEATBACK COVER


    1. Attach the 4 claws to install the cover.

  10. Click here

    INSTALL SEAT CUSHION COVER WITH PAD


    1. Install the seatback cover with pad.

    2. A015BML

      w/ Center Armrest:

      Pull out the seat belt.

    3. A0158Z6

      w/o Center Armrest:

      Pull out the seat belt.

    4. w/ Rear Seat Side Airbag:

      Pass the side airbag wire harness through the hole in the seatback.

    5. w/ Seat Heater System:

      Pass the seatback heater wire harness through the hole in the seatback.


      1. A015APP
      2. A015AWWE01

        Connect the seatback heater wire harness and install a new cable tie.

    6. A0159P8

      w/ Rear Seat Side Airbag:

      Install the seatback cover bracket to the seat frame with the cap nut.

      5.5 N*m 56 kgf*cm 49 in.*lbf
      Note:

      After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.

    7. A0158CZE01

      w/ Center Armrest:

      Using hog ring pliers, install new hog rings to the seatback frame.

    8. A0159WZE01

      w/o Center Armrest:

      Using hog ring pliers, install new hog rings to the seatback frame.

  11. Click here

    CONNECT NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. Connect the belt anchor.

      Note:

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

  12. Click here

    INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH


    1. Install the belt with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

      Tip:

      The No. 1 seat 3 point type belt anchor is fixed with the same bolt as the rear No. 1 seat inner belt LH. Therefore, connect it when installing the rear No. 1 seat inner belt LH.

  13. Click here

    INSTALL REAR SEAT UNDER TRAY COVER LH


    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  14. Click here

    INSTALL REAR SEAT CUSHION COVER RH


    1. Attach the 2 claws to install the cover.

    2. Install the 4 screws.

  15. Click here

    INSTALL REAR UNDER SIDE COVER LH


    1. Attach the 2 claws and 2 clips to install the cover.

    2. Install the 5 screws.

    3. A0155YN

      Attach the 10 claws.

  16. Click here

    INSTALL REAR SEATBACK STAY COVER LH


    1. Attach the 2 claws to install the cover.

    2. Install the screw.

  17. Click here

    INSTALL SEAT BELT ANCHOR COVER CAP


    1. A0159WX

      Install the anchor cover cap with the screw.

    2. A015C6J

      Attach the claw to close the cap.

  18. Click here

    INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY RH


    1. Install the hinge with the 2 nuts.

      42 N*m 428 kgf*cm 31 ft.*lbf
  19. Click here

    INSTALL REAR NO. 1 SEAT HINGE SUB-ASSEMBLY LH


    1. A0155TF

      Attach the cable clamp to connect the cable.

    2. A0157X7

      Install the hinge with the 2 nuts.

      42 N*m 428 kgf*cm 31 ft.*lbf

    3. w/ Rear Seat Side Airbag:

      Attach the wire harness clamp.

    4. w/ Seat Heater System:

      Attach the wire harness clamp.

  20. Click here

    INSTALL REAR NO. 2 SEAT PROTECTOR


    1. Install the wire harness, and attach 2 claws to close the protector.

    2. A015BO6

      Attach the claw to install the protector to the seat hinge.

    3. Install the clip.

    4. A0155UV

      w/ Rear Seat Side Airbag:

      Attach the claw to install the wire harness connector.

    5. w/ Seat Heater System:

      Attach the claw to install the wire harness connector.

  21. Click here

    INSTALL REAR NO. 2 SEAT LEG SIDE COVER


    1. A015AUN

      Pass the fold seat stopper band through the seat leg side cover and attach it to the seat cushion frame with the bolt.

    2. A0156BB

      Attach the 4 claws to install the seat leg side cover.

    3. Install the 4 screws.

  22. Click here

    INSTALL UPPER SEAT TRACK RAIL COVER RH


    1. Attach the 2 claws to install the cover.

  23. Click here

    INSTALL UPPER SEAT TRACK RAIL COVER LH


    1. Attach the 2 claws to install the cover.

  24. Click here

    INSTALL REAR NO. 1 SEAT RECLINING COVER RH


    1. Attach the 4 claws to install the cover.

    2. Install the 2 screws.

  25. Click here

    INSTALL REAR NO. 1 SEAT RECLINING COVER LH


    1. Attach the 3 claws in the order shown in the illustration to install the cover.

    2. Install the 2 screws.

  26. Click here

    INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. Install the release handle with the screw.

  27. Click here

    INSTALL SEAT ADJUSTER BOLT COVER


    1. Attach the 2 claws to install the cover.

  28. Click here

    INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    1. Install the rear No. 1 seat assembly (Click here).