FUEL FILTER REPLACEMENT


  1. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  2. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE NO. 1 FUEL TUBE PROTECTOR


    1. A0157LV

      Remove the 4 bolts and No. 1 fuel tube protector.

  5. DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY


    1. A015727E03
      Text in Illustration
      *1 Retainer
      *2 Nylon Tube
      *3 Pipe
      *4 O-Ring
      *5 Connector

      Pull up the retainer and disconnect the No. 2 fuel main tube.

      Note


      • Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

      • Do not use any tools to separate the pipe and connector.

      • Do not forcefully bend or twist the nylon tube.

      • Check for foreign matter on the pipe seal surface. Clean if necessary.

      • Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

      • If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

  6. DISCONNECT FUEL MAIN TUBE


    1. A015607E03
      Text in Illustration
      *1 Retainer
      *2 Nylon Tube
      *3 Pipe
      *4 O-Ring
      *5 Connector

      Pull up the retainer and disconnect the fuel main tube.

      Note


      • Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

      • Do not use any tools to separate the pipe and connector.

      • Do not forcefully bend or twist the nylon tube.

      • Check for foreign matter on the pipe seal surface. Clean if necessary.

      • Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

      • If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

  7. REMOVE FUEL FILTER ASSEMBLY


    1. A015637

      Remove the 2 bolts and fuel filter.

  8. INSTALL FUEL FILTER ASSEMBLY


    1. Install the fuel filter with the 2 bolts.

      Torque:
      20 N*m  { 199 kgf*cm, 14 ft.*lbf }

  9. CONNECT FUEL MAIN TUBE


    1. A0159CSE03
      Text in Illustration
      *1 Retainer
      *2 Nylon Tube
      *3 Pipe
      *4 O-Ring
      *5 Connector

      Connect the fuel main tube and push the retainer.

      Note


      • Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

      • After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

      Tech Tips

      Push the parts together firmly until a "click" sound is heard.

  10. CONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY


    1. A0156SOE03
      Text in Illustration
      *1 Retainer
      *2 Nylon Tube
      *3 Pipe
      *4 O-Ring
      *5 Connector

      Connect the No. 2 fuel main tube and push the retainer.

      Note


      • Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

      • After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

      Tech Tips

      Push the parts together firmly until a "click" sound is heard.

  11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  12. INSPECT FOR FUEL LEAK


    1. Make sure that there are no fuel leaks after performing maintenance on the fuel system.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON and turn the GTS on.

        Note

        Do not start the engine.

      3. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

      4. Check that there are no leaks from the fuel system.

        If there are fuel leaks, repair or replace parts as necessary.

      5. Turn the ignition switch off.

      6. Disconnect the GTS from the DLC3.

  13. INSTALL NO. 1 FUEL TUBE PROTECTOR


    1. Install the No. 1 fuel tube protector and 4 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }