POWER MIRROR CONTROL SYSTEM (w/ Memory) Power Retractable Mirrors do not Operate with Power Retract Mirror Switch

SYSTEM DESCRIPTION

The main body ECU (multiplex network body ECU) receives the retractable outer mirror switch signal from the outer mirror switch assembly (retractable outer mirror switch). The main body ECU then sends the mirror retract/return signal to each outer mirror control ECU assembly via CAN communication. Based on this signal, each outer mirror control ECU assembly retracts or returns the outer rear view mirror assembly.

WIRING DIAGRAM

INSPECTION PROCEDURE

PROCEDURE

1. CHECK CAN COMMUNICATION SYSTEM

   
   

   1. Use the GTS to check if the CAN communication system is functioning normally Click here.

      OK
      CAN communication DTCs are not output.

   
   

   NG

   GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) Click here

   OK

2. READ VALUE USING GTS (RETRACTABLE OUTER MIRROR SWITCH)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the engine switch on (IG).

   3. Turn the GTS on.

   4. Enter the following menus: Body Electrical / Main Body / Data List.

   5. Read the Data List according to the display on the GTS.

      Main Body

      Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
      Outer Mirror Fold SW	Retractable outer mirror switch signal / ON or OFF	ON: Retractable outer mirror switch in retract position OFF: Retractable outer mirror switch in driving position	-

      OK
      On the GTS screen, ON or OFF is displayed for each item according to the above.

   
   

   NG

   INSPECT RETRACTABLE OUTER MIRROR SWITCH Click here

   OK

3. PERFORM ACTIVE TEST USING GTS (MIRROR RETRACT FUNCTION)

   
   

   1. Enter the following menus: Body Electrical / Mirror L or Mirror R / Active Test.

   2. Perform the Active Test according to the display on the GTS.

      Mirror L / Mirror R

      Tester Display	Test Part	Control Range	Diagnostic Note
      Mirror Fold/Return	Mirror retract operation	Fold / Return	Operate with engine switch on (IG) and the vehicle stopped. This test activates the Fold / Return. This operation can be confirmed by watching the mirror move in the desired direction.

      Result
      Result Proceed to Outer rear view mirror assemblies operate normally A Outer rear view mirror assembly (front passenger door) does not operate normally B Outer rear view mirror assembly (driver door) does not operate normally C

   
   

   B

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) Click here

   C

   INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) Click here

   A

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR)

   
   
   1. 

      Text in Illustration

      *1	(A) Forward Position
      *2	(B)
      *3	(C) Driving Position
      *4	(D)
      *5	(E) Retracted Position
      *a	Component without harness connected (Outer Rear View Mirror Assembly (Front Passenger Door))

      Remove the outer rear view mirror assembly (front passenger door) Click here.

   2. When checking each mirror position, set the mirror position by hand. Apply battery voltage and check the mirror movement.

      Note

      
      

      • Disconnect and reconnect the battery for each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      OK

      Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to (E) Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Between forward position (A) and driving position (C) Moves from (B) to (E) Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to (E) Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Between driving position (C) and retracted position (E) Moves from (D) to (E) Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Retracted position (E) Moves from (E) to (C)

   
   

   NG

   REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (FRONT PASSENGER DOOR) Click here

   OK

   REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR) Click here

5. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR)

   
   
   1. 

      Text in Illustration

      *1	(A) Forward Position
      *2	(B)
      *3	(C) Driving Position
      *4	(D)
      *5	(E) Retracted Position
      *a	Component without harness connected (Outer Rear View Mirror Assembly (Driver Door))

      Remove the outer rear view mirror assembly (driver door) Click here.

   2. When checking each mirror position, set the mirror position by hand. Apply battery voltage and check the mirror movement.

      Note

      
      

      • Disconnect and reconnect the battery for each mirror position check.

      • The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

      OK

      Measurement Condition Mirror Position Specified Condition Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Forward position (A) Moves from (A) to (E) Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Forward position (A) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Between forward position (A) and driving position (C) Moves from (B) to (E) Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Between forward position (A) and driving position (C) Moves from (B) to (A) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Driving position (C) Moves from (C) to (E) Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Driving position (C) Does not move Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Between driving position (C) and retracted position (E) Moves from (D) to (E) Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Between driving position (C) and retracted position (E) Moves from (D) to (C) Battery positive (+) → Terminal 3 (MR) Battery negative (-) → Terminal 11 (MF) Retracted position (E) Does not move Battery negative (-) → Terminal 3 (MR) Battery positive (+) → Terminal 11 (MF) Retracted position (E) Moves from (E) to (C)

   
   

   NG

   REPLACE OUTER REAR VIEW MIRROR ASSEMBLY (DRIVER DOOR) Click here

   OK

   REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR) Click here

6. INSPECT RETRACTABLE OUTER MIRROR SWITCH

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Retractable Outer Mirror Switch)
      *b	Driving position
      *c	Retract position
      *d	AUTO position

      Remove the retractable outer mirror switch Click here.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 2 (MR) - 4 (E) Except retract position Below 1 Ω 2 (MR) - 4 (E) Retract position 10 kΩ or higher

   
   

   NG

   REPLACE RETRACTABLE OUTER MIRROR SWITCH Click here

   OK

7. CHECK HARNESS AND CONNECTOR (RETRACTABLE OUTER MIRROR SWITCH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

   
   

   1. Disconnect the H10 connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition H72-2 (MR) - H10-28 (RET) Always Below 1 Ω H72-2 (MR) - Body ground Always 10 kΩ or higher H72-4 (E) - Body ground Always 10 kΩ or higher

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here