OUTER MIRROR CONTROL ECU REMOVAL

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (- ) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01G4MY

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

  4. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01G55U

      Using a moulding remover, disengage the 2 clips, 6 claws and 2 guides as shown in the illustration.

    2. Disconnect each connector and remove the multiplex network master switch assembly with front door armrest base panel.

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01G72A

      Using a moulding remover, disengage the 2 clips, 6 claws and 2 guides as shown in the illustration.

    2. Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.

  6. REMOVE DOOR PULL HANDLE COVER


    1. A01G53E

      Remove the door pull handle cover.

  7. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01G6KGE01
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  8. REMOVE FRONT DOOR NO. 1 STIFFENER CUSHION


    1. A01G98H

      Remove the screw and front door No. 1 stiffener cushion.

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01G517E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the front door panel.

    2. A01G7VV

      Remove the 3 screws.

    3. A01G6RQ

      Using a clip remover, disengage the 11 clips.

    4. A01G7HME01
      Text in Illustration
      *1 Reference Boss
      *2 Front Door Inner Glass Weatherstrip

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the front door panel.

    6. Raise the front door trim board sub-assembly and disconnect the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    7. w/ Memory:


      1. Disconnect the connector.

    8. w/ Illumination:


      1. Disconnect the connector.

    9. A01G5K5

      Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

  10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A01G7XDE01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  11. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY


    1. Disconnect 2 connectors.

    2. A01G81S

      Remove the 2 screws and outer mirror control ECU assembly.