HOOD LOCK CONTROL CABLE ASSEMBLY INSTALLATION


  1. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD)


    1. Pass the hood lock control cable assembly into the cabin.

    2. Pass the cable through the upper radiator support.

    3. Engage the hood cable grommet.

    4. Engage the 5 clamps to install the hood lock control cable assembly.

  2. INSTALL HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD)


    1. Pass the hood lock control cable assembly into the cabin.

    2. Pass the cable through the upper radiator support.

    3. Engage the hood cable grommet.

    4. Engage the 4 clamps to install the hood lock control cable assembly.

  3. INSTALL HOOD LOCK ASSEMBLY


    1. for LHD:


      1. A01G6IJ

        Apply MP grease to the sliding areas of the lock.

    2. for RHD:


      1. A01G5BA

        Apply MP grease to the sliding areas of the lock.

    3. Connect the hood lock control cable assembly.

    4. Install the hood lock assembly with the 3 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    5. Engage the clamp.

    6. Connect the connector.

  4. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. Connect the hood lock control cable assembly and install the hood lock control lever sub-assembly.

  5. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  6. INSTALL COWL SIDE TRIM BOARD LH (for LHD)


    1. Engage the clip and claw.

    2. Install the cowl side trim board LH with the clip.

  7. INSTALL FRONT DOOR SCUFF PLATE LH (for LHD)


    1. Engage the 10 claws to install the front door scuff plate LH.

  8. INSTALL COWL SIDE TRIM BOARD RH (for RHD)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  9. INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  10. INSTALL FRONT FENDER LINER LH (for LHD)

    Tech Tips

    Use the same procedure as for the RH side Click here.

  11. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for LHD)

    Tech Tips

    Use the same procedure as for the RH side Click here.

  12. INSTALL FRONT WHEEL LH (for LHD)

    Torque:
    103 N*m  { 1049 kgf*cm, 76 ft.*lbf }

  13. INSTALL FRONT FENDER LINER RH (for RHD)


    1. Install the front fender liner RH with 2 new grommets.

    2. Using a 4 mm hexagon wrench, install the 3 hexagon screws.

    3. Install the 6 clips.

    4. Install the 4 screws and bolt.

    5. A01G7QKE01
      Text in Illustration
      *a Correct
      *b Incorrect

      Install the pin hold clip as shown in the illustration.

      Note

      Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is aligned vertically.

  14. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)


    1. Install the front wheel opening extension pad RH with the 3 screws.

  15. INSTALL FRONT WHEEL RH (for RHD)

    Torque:
    103 N*m  { 1049 kgf*cm, 76 ft.*lbf }

  16. INSTALL COOL AIR INTAKE DUCT SEAL


    1. Install the cool air intake duct seal with the 9 clips.

  17. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

    Click here

  18. ADJUST HOOD SUB-ASSEMBLY

    Click here