BLIND SPOT MONITOR SYSTEM, Diagnostic DTC:C1AB0

DTC Code DTC Name
C1AB0 Short to +B in Outer Mirror Indicator(Master)

DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH detects a +B short in the outer rear view mirror indicator LH.

DTC No. DTC Detection Condition Trouble Area
C1AB0

    Both of the following conditions are met:

  • Blind spot monitor main switch (warning canceling switch assembly) is on.


  • The blind spot monitor sensor is not sending voltage to the indicator but the indicator receives voltage above a specified level for a specified period of time.

  • Outer rear view mirror LH (outer rear view mirror indicator LH)

  • Outer rear view mirror assembly LH

  • Wire harness or connector

  • Blind spot monitor sensor LH

  • Outer mirror control ECU assembly LH

WIRING DIAGRAM

A01G9IEE19

INSPECTION PROCEDURE

Note

When checking for DTCs, make sure that the blind spot monitor main switch (warning canceling switch assembly) is on.

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs Click here.

    2. Recheck for DTCs and check if the same DTC is output again.

      OK
      No DTCs are output.

    NG

    CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR LH) Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  2. CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR LH)


    1. Disconnect the U8 blind spot monitor sensor LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U8-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V

    NG

    CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH) Click here

    OK

    REPLACE BLIND SPOT MONITOR SENSOR LH Click here

  3. CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER REAR VIEW MIRROR ASSEMBLY LH)


    1. Disconnect the IND2 outer rear view mirror LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U8-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V

    NG

    CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH) Click here

    OK

    REPLACE OUTER REAR VIEW MIRROR LH Click here

  4. CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)


    1. Disconnect the z7 outer mirror control ECU assembly LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U8-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V

    NG

    CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH) Click here

    OK

    REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH Click here

  5. CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR SENSOR LH - OUTER MIRROR CONTROL ECU ASSEMBLY LH)


    1. Disconnect the M9 outer mirror control ECU assembly LH connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      U8-4 (OMIL) - Body ground Engine switch on (IG) Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH Click here