POWER MIRROR CONTROL SYSTEM(w/ Memory) Power Mirror cannot be Adjusted with Power Mirror Switch

DESCRIPTION

The main body ECU (multiplex network body ECU) detects the mirror adjust switch status and sends the signal to each outer mirror control ECU assembly via CAN communication. Based on this signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors to adjust the mirror surface position.

WIRING DIAGRAM

A0008OME11

CAUTION / NOTICE / HINT

Note

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Use the GTS to check if the CAN communication system is functioning normally Click here.

      OK
      CAN communication DTCs are not output.

    NG

    GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) Click here

    OK

  2. READ VALUE USING GTS (OUTER MIRROR SWITCH ASSEMBLY)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Mirror Selection SW (R) Mirror select switch signal for RH mirror / ON or OFF

      ON: Mirror select switch in R position

      OFF: Mirror select switch off or in L position

      		 -
      Mirror Selection SW (L) Mirror select switch signal for LH mirror / ON or OFF

      ON: Mirror select switch in L position

      OFF: Mirror select switch off or in R position

      		 -
      Mirror Position SW (R) Mirror adjust switch signal (Right) / ON or OFF

      ON: Mirror adjust switch pressed right

      OFF: Mirror adjust switch not pressed right

      		 Check with the mirror select switch in any position except neutral
      Mirror Position SW (L) Mirror adjust switch signal (Left) / ON or OFF

      ON: Mirror adjust switch pressed left

      OFF: Mirror adjust switch not pressed left

      		 Check with the mirror select switch in any position except neutral
      Mirror Position SW (Up) Mirror adjust switch signal (Up) / ON or OFF

      ON: Mirror adjust switch pressed up

      OFF: Mirror adjust switch not pressed up

      		 Check with the mirror select switch in any position except neutral
      Mirror Position SW (Dwn) Mirror adjust switch signal (Down) / ON or OFF

      ON: Mirror adjust switch pressed down

      OFF: Mirror adjust switch not pressed down

      		 Check with the mirror select switch in any position except neutral
      OK
      On the GTS screen, ON or OFF is displayed for each item according to the table above.

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

  3. INSPECT OUTER MIRROR SWITCH ASSEMBLY


    1. Remove the outer mirror switch assembly Click here.

    2. Inspect the outer mirror switch assembly Click here.


    NG

    REPLACE OUTER MIRROR SWITCH ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU)


    1. Disconnect the H81 outer mirror switch assembly connector.

    2. Disconnect the H9 main body ECU (multiplex network body ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H81-14 (E) - H9-15 (MIRE) Always Below 1 Ω
      H81-16 (M+) - H9-13 (MIRB) Always Below 1 Ω
      H81-13 (MSW) - H9-14 (MIRS) Always Below 1 Ω
      H81-14 (E) - Body ground Always 10 kΩ or higher
      H81-16 (M+) - Body ground Always 10 kΩ or higher
      H81-13 (MSW) - Body ground Always 10 kΩ or higher

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR