Click here

WINDOW DEFOGGER SYSTEM Rear Window Defogger System does not Operate

Click here
Click here
DTC Code DTC Name
  Rear Window Defogger System does not Operate
Click here

DESCRIPTION

When the rear window defogger switch on the Radio Receiver Assembly is pressed, the operation signal is transmitted to the air conditioning amplifier assembly through the CAN communication line. When the air conditioning amplifier assembly receives the signal, it turns on the engine room junction block assembly to operate the rear window defogger.

Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Click here

Note:

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • If the auxiliary battery voltage becomes low, rear window defogger system operation is canceled to prioritize supplying power to the power steering system.

  • The window defogger system uses the CAN communication. First, confirm that there is no malfunction in the CAN communication line. Refer to How to Proceed with Troubleshooting (Click here).

Click here

PROCEDURE


  1. Click here

    CHECK AIR CONDITIONING SYSTEM


    1. Check the air conditioning system.

      Tip:

      Both the window defogger system operation signal and air conditioning system operation signal are transmitted to the air conditioning amplifier assembly through same communication line.

      OK
      The air conditioning system operates normally.

  2. Click here

    PERFORM ACTIVE TEST USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Air Conditioner / Active Test.

    5. Perform the Active Test according to the display on the GTS.

      Table 1. Air Conditioner
      Tester Display Test Part Control Range Diagnostic Note
      Defogger Relay (Rear) Rear window defogger OFF or ON -
      OK
      The window defogger system operates normally.

  3. Click here

    REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY


    1. Replace the air conditioning amplifier assembly with a new or known good one (Click here).

    2. Check that the window defogger system operates normally.

      OK
      The window defogger system operates normally.
      Table 2. Result
      Result Proceed to
      OK A
      NG (w/o Navigation System) B
      NG (w/ Navigation System) C

    • A

      END (AIR CONDITIONING AMPLIFIER ASSEMBLY WAS DEFECTIVE)

    • B

      REPLACE RADIO RECEIVER ASSEMBLY (Click here)

    • C

      REPLACE RADIO RECEIVER ASSEMBLY (Click here)

  4. Click here

    CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY


    1. Using a voltmeter, check the signal reading of the engine room junction block assembly (Click here).

      OK
      Output signal reading is normal.

    • OKClick here
    • NG

      INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY (RESULTS OF SIGNAL READING CHECK) (Click here)

  5. Click here

    CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK ASSEMBLY - POWER SOURCE AND BODY GROUND)


    1. A0005W1E01

      Remove the engine room junction block assembly from the engine room relay block and junction block assembly.

      Table 3. Text in Illustration
      *a

      Component without engine room junction block assembly

      (Engine Room Relay Block and Junction Block Assembly)

      		 - -

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A-1 (BATT) - Body ground Power switch off 11 to 14 V
      B-1 (ALT) - Body ground Power switch off 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1F-3 (GND1) - Body ground Always Below 1 Ω
      1G-4 (GND2) - Body ground Always Below 1 Ω

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)


    1. Disconnect the H54 air conditioning amplifier assembly connector.

    2. Disconnect the 1F engine room junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      H54-38 (RDFG) - 1F-4 (DEFS) Always Below 1 Ω
      1F-4 (DEFS) - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  7. Click here

    CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY


    1. Reconnect the 1F engine room junction block assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H54-38 (RDFG) - Body ground Power switch on (IG) 11 to 14 V

  8. Click here

    CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


    1. Reconnect the H54 air conditioning amplifier assembly connector.

    2. A000700E03

      Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      H54-38 (RDFG) - H54-14 (GND) Power switch on (IG), rear window defogger switch off 11 to 14 V
      H54-38 (RDFG) - H54-14 (GND) Power switch on (IG), rear window defogger switch on Below 2.2 V
      Table 4. Text in Illustration
      *a

      Component with harness connected

      (Air Conditioning Amplifier Assembly)

  9. Click here

    CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - REAR WINDOW DEFOGGER WIRE)


    1. Disconnect the P18 back window glass (rear window defogger wire) auxiliary battery side connector.

    2. Disconnect the 1N engine room junction block assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1N-1 (RDEF) - P18-1 Always Below 1 Ω

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  10. Click here

    CHECK ENGINE ROOM JUNCTION BLOCK ASSEMBLY


    1. Reconnect the 1N engine room junction block assembly connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      P18-1 - Body ground Power switch on (IG), rear window defogger switch on 11 to 14 V
      P18-1 - Body ground Power switch on (IG), rear window defogger switch off Below 1 V

  11. Click here

    CHECK HARNESS AND CONNECTOR (BACK WINDOW GLASS (REAR WINDOW DEFOGGER WIRE) - BODY GROUND)


    1. Disconnect the R1 back window glass (rear window defogger wire) ground side connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R1-1 - Body ground Always Below 1 Ω

    • OK

      REPAIR OR REPLACE BACK WINDOW GLASS (REAR WINDOW DEFOGGER WIRE) (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR