PARKING BRAKE ASSEMBLY DISASSEMBLY

CAUTION / NOTICE / HINT

Note


  • When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

  • While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work Click here.

  2. DISABLE BRAKE CONTROL (for LHD)

    Click here

  3. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

    Tech Tips

    Use the same procedure as for LHD Click here.

  4. REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

    Click here

  5. DISABLE BRAKE CONTROL (for RHD)

    Click here

  6. REMOVE REAR WHEEL

  7. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  8. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

  9. REMOVE REAR DISC

    Click here

  10. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Front Side)


    1. A0006KW

      Remove the parking brake shoe return tension spring.

  11. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Rear Side)


    1. A0009KG

      Remove the parking brake shoe return tension spring.

  12. REMOVE PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Front Side)


    1. A0004MOE04

      Using SST, remove the parking brake shoe hold down compression spring.

      SST
      09718-00011

  13. REMOVE PARKING BRAKE SHOE STRUT


    1. A000810

      Pull the No. 1 parking brake shoe assembly towards the front of the vehicle by hand as shown in the illustration.

    2. A0003TP

      Remove the parking brake shoe strut.

  14. REMOVE PARKING BRAKE SHOE HOLD DOWN COMPRESSION SPRING (for Rear Side)


    1. A0008EYE04

      Using SST, remove the parking brake shoe hold down compression spring.

      SST
      09718-00011

  15. SEPARATE PARKING BRAKE SHOE LEVER


    1. A0007M2

      Expand the No. 1 and No. 2 parking brake shoe assemblies outward by hand and pull downward to separate them from the parking brake plate.

    2. Separate the parking brake shoe lever from the No. 2 parking brake shoe assembly.

  16. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A0008X1

      Remove the parking brake shoe adjusting screw set.

  17. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A0003HC

      Remove the No. 1 parking brake shoe assembly.

  18. REMOVE PARKING BRAKE SHOE RETURN TENSION SPRING (for Lower Side)


    1. A0007Z2

      Remove the parking brake shoe return tension spring.

  19. REMOVE PARKING BRAKE SHOE LEVER


    1. A000882

      Using needle-nose pliers, remove the parking brake shoe lever from the No. 3 parking brake cable assembly as shown in the illustration.

  20. REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN


    1. A000935

      Remove the parking brake shoe hold down spring pin (for front side).

    2. A00081X

      Remove the parking brake shoe hold down spring pin (for rear side).