Click here

AIR CONDITIONING UNIT REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

Note:

Make sure to select FACE mode before disconnecting the cable from the negative (-) battery terminal.

Click here

PROCEDURE


  1. Click here

    RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

    Click here

  2. Click here

    REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    (Click here)

  3. Click here

    REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

    for LHD: (Click here)

    for RHD: (Click here)

  4. Click here

    DISCONNECT NO. 1 BRAKE ACTUATOR TUBE


    1. A0003U3

      Remove the nut and disconnect the No. 1 brake actuator tube.

  5. Click here

    DISCONNECT HEATER OUTLET WATER HOSE


    1. A0005TY

      Using pliers, grip the claws of the clip and slide the clip to disconnect the heater outlet water hose.

      Note:

      • Do not apply excessive force to the heater outlet water hose.

      • Prepare a drain pan or cloth in case the coolant leaks.

  6. Click here

    DISCONNECT HEATER INLET WATER HOSE


    1. A0006NL

      Using pliers, grip the claws of the clip and slide the clip to disconnect the heater inlet water hose.

      Note:

      • Do not apply excessive force to the heater inlet water hose.

      • Prepare a drain pan or cloth in case the coolant leaks.

  7. Click here

    DISCONNECT SUCTION PIPE SUB-ASSEMBLY


    1. A0004I9

      Remove the bolt and rotate the hook connector.

    2. A0006T1

      Disconnect the suction pipe sub-assembly.

    3. Remove the O-ring from the suction pipe sub-assembly.

      Note:

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

  8. Click here

    DISCONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY


    1. A000655

      Disconnect the air conditioner tube and accessory assembly.

    2. Remove the O-ring from the air conditioner tube and accessory assembly.

      Note:

      Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

  9. Click here

    REMOVE FRONT SEAT ASSEMBLY LH

    (Click here)

  10. Click here

    REMOVE AUDIO AMPLIFIER COVER

    Click here

  11. Click here

    REMOVE STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET

    Click here

  12. Click here

    REMOVE FRONT SEAT ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

  13. Click here

    REMOVE AUDIO AMPLIFIER COVER (w/ Telematics Transceiver)

    Click here

  14. Click here

    REMOVE TELEMATICS TRANSCEIVER WITH MAYDAY BATTERY (w/ Telematics Transceiver)

    Click here

  15. Click here

    REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

    (Click here)

  16. Click here

    REMOVE STEERING POST ASSEMBLY

    (Click here)

  17. Click here

    REMOVE WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

    Click here

  18. Click here

    REMOVE DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)

    for RHD: (Click here)

  19. Click here

    REMOVE HYBRID VEHICLE CONTROL ECU ASSEMBLY

    Click here

  20. Click here

    REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

    Click here

  21. Click here

    REMOVE WIRING HARNESS CLAMP BRACKET (for RHD)


    1. A00046M

      Remove the nut.

    2. Disengage the claw to remove the wiring harness clamp bracket.

  22. Click here

    REMOVE ECU INTEGRATION BOX RH

    for LHD: (Click here)

    for RHD: (Click here)

  23. Click here

    REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

    Click here

  24. Click here

    REMOVE FLOOR CARPET HOOK


    1. A0003PKE07

      Disengage the 6 guides.

      Table 1. Text in Illustration
      *A for LH Side
      *B for RH Side
    2. A0006IGE07

      Disengage the 6 clamps and remove the 6 floor carpet hooks.

      Table 2. Text in Illustration
      *A for LH Side
      *B for RH Side
  25. Click here

    REMOVE REAR AIR DUCT GUIDE LH


    1. A0009AS

      Disengage the guide.

    2. Turn back the floor carpet as shown in the illustration.

    3. A0008IJ

      Disengage the 4 claws to remove the rear air duct guide LH.

  26. Click here

    REMOVE REAR NO. 2 AIR DUCT


    1. A00079A

      Disengage the 2 claws to remove the rear No. 2 air duct.

  27. Click here

    REMOVE FLOOR CARPET BRACKET LH


    1. A0007B6

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket LH.

  28. Click here

    REMOVE FRONT FLOOR CAUTION PLATE COVER


    1. A0006AN

      Using a moulding remover, disengage the claw and guide, and remove the front floor caution plate cover.

  29. Click here

    REMOVE REAR AIR DUCT GUIDE RH


    1. A0008RG

      Disengage the guide.

    2. Turn back the floor carpet as shown in the illustration.

    3. A0003QQ

      Disengage the 4 claws to remove the rear air duct guide RH.

  30. Click here

    REMOVE REAR NO. 1 AIR DUCT


    1. A0008RI

      Disengage the 2 claws to remove the rear No. 1 air duct.

  31. Click here

    REMOVE FLOOR CARPET BRACKET RH


    1. A0006PD

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket RH.

  32. Click here

    REMOVE NO. 1 CONSOLE BOX MOUNTING BRACKET (for LHD)

    Click here

  33. Click here

    REMOVE NO. 1 CONSOLE BOX DUCT


    1. A00052U

      Remove the clip and No. 1 console box duct.

  34. Click here

    REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR


    1. A0008XV

      Disconnect the connector and cooler thermistor hose, and remove the cooler (room temp. sensor) thermistor.

  35. Click here

    REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    1. A0009MD

      Disconnect the connector.

    2. Disengage the clamp.

    3. A0005HFE07

      Remove the screw.

      Table 3. Text in Illustration
      *a Screw
      *b Bolt
      *c Nut

    4. Remove the bolt, 2 nuts and No. 1 instrument panel brace sub-assembly.

  36. Click here

    REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


    1. A0007G8E07

      Remove the bolt and disconnect the earth wire.

      Table 4. Text in Illustration
      *a Earth Wire

    2. Disconnect the connector.

    3. Disengage each clamp.

    4. A0006C6E07

      Remove the screw.

      Table 5. Text in Illustration
      *a Screw
      *b Bolt
      *c Nut

    5. Remove the bolt, 2 nuts and No. 2 instrument panel brace sub-assembly.

  37. Click here

    REMOVE NO. 1 HEATER TO REGISTER DUCT


    1. A0007KV

      Disengage the clamp.

    2. Using a clip remover, remove the 3 clips and No. 1 heater to register duct.

  38. Click here

    REMOVE INSTRUMENT PANEL SAFETY PAD CAP


    1. A0005GVE07

      Put protective tape around the 5 instrument panel safety pad caps.

      Table 6. Text in Illustration
      *A for LH Side
      *B for RH Side
      *a Protective Tape

    2. Using a screwdriver, remove the 5 instrument panel safety pad caps.

  39. Click here

    REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

    Note:

    • Be sure to support the air conditioning unit assembly when removing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

    • When disassembling the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.


    1. A0005LR

      Disengage each clamp.

    2. w/ Telematics Transceiver:


      1. A0009B3

        Disengage each clamp.

    3. A0009A2

      Disengage the 3 claws to open the 3 clamps as shown in the illustration.

    4. A0008D5E01

      Disconnect the connector from the airbag sensor assembly as shown in the illustration.

      Table 7. Text in Illustration
      *1 Airbag Sensor Assembly - -
      Note:

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    5. Disconnect each connector.

    6. Disengage each clamp.

    7. for LHD:


      1. Remove the lower shift lever assembly (Click here).

      2. Remove the shift lever support (Click here).

    8. A0006IS

      Remove the bolt.

    9. Disconnect the connector.

    10. A0005K0E02

      Using a screwdriver, disengage the 2 claws to unlock the retainer as shown in the illustration.

      Table 8. Text in Illustration
      *a Retainer *b Protective Tape
    11. A00097U

      Disengage the claw and disconnect the airbag connector as shown in the illustration.

    12. for LHD:


      1. A0005K4E04

        Remove the 2 nuts and disconnect the connector holder.

        Table 9. Text in Illustration
        *a Connector Holder *b Protector
        *c Earth Wire *d Nut
        *e Bolt - -

      2. Remove the nut and disconnect the protector.

      3. Remove the 4 bolts and disconnect the 4 earth wires.

      4. Disconnect the connector.

      5. Disengage each clamp.

    13. for RHD:


      1. A0005L1E02

        Remove the 2 nuts and disconnect the connector holder.

        Table 10. Text in Illustration
        *a Connector Holder *b Protector
        *c Earth Wire *d Nut
        *e Bolt - -

      2. Remove the 4 bolts and disconnect the 4 earth wires.

      3. Disconnect the connector.

      4. Disengage each clamp.

    14. A0005B4

      Remove the 2 hole plugs.

    15. A0005KB

      Remove the 2 bolts.

    16. A0009OHE02

      Disconnect the drain cooler hose.

      Table 11. Text in Illustration
      *1 Instrument Panel Reinforcement Assembly - -
      *a Movable Collar *b Body
      *c Step 1 *d Step 2
      *e Step 3 *f Step 4

    17. Remove the 6 bolts and nut as shown in the illustration.

    18. A00064B

      Disengage the 3 guides and remove the instrument panel reinforcement with air conditioning unit as shown in the illustration.

  40. Click here

    REMOVE AIR CONDITIONING UNIT ASSEMBLY


    1. A0005OS

      Remove the 3 bolts and air conditioning unit assembly from the instrument panel reinforcement assembly.

  41. Click here

    REMOVE BLOWER ASSEMBLY

    for LHD: (Click here)

    for RHD: (Click here)

  42. Click here

    REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for LHD)


    1. A000446E05

      Disconnect each connector.

      Table 12. Text in Illustration
      *A for 3 Zone Type - -

    2. Disengage each clamp and remove the air conditioning harness assembly.

  43. Click here

    REMOVE AIR CONDITIONING HARNESS ASSEMBLY (for RHD)


    1. A0006OUE01

      Disconnect each connector.

      Table 13. Text in Illustration
      *A for 3 Zone Type - -

    2. Disengage each clamp and remove the air conditioning harness assembly.

  44. Click here

    REMOVE NO. 6 HEATER TO REGISTER DUCT ASSEMBLY


    1. A0005G5

      Disengage the 2 claws and 2 guides, and remove the No. 6 heater to register duct assembly as shown in the illustration.

  45. Click here

    REMOVE NO. 1 AIR DUCT SUB-ASSEMBLY


    1. A0008T1

      Disengage the 2 claws and guide, and remove the No. 1 air duct sub-assembly as shown in the illustration.

  46. Click here

    REMOVE NO. 4 AIR DUCT SUB-ASSEMBLY (for RHD)


    1. A0009GS

      Disengage the 2 claws and guide to remove the No. 4 air duct sub-assembly as shown in the illustration.

  47. Click here

    REMOVE HEATER PACKING


    1. A0009M0

      Remove the heater packing as shown in the illustration.

  48. Click here

    REMOVE COOLER THERMISTOR HOSE


    1. A00076X

      Disengage the clamp and remove the cooler thermistor hose.

  49. Click here

    REMOVE ASPIRATOR PIPE


    1. A0007D9

      Disengage the 2 claws and remove the aspirator pipe.

  50. Click here

    REMOVE DRAIN COOLER HOSE


    1. A0008L0

      Remove the drain cooler hose.