ТРОС МЕХАНИЗМА ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ СНЯТИЕ


  1. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    1. Remove the front exhaust pipe assembly Click here.

  2. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

  5. REMOVE NO. 1 ENGINE COVER


    1. A01INMI

      Hold the rear of the No. 1 engine cover and slowly raise it to detach the clip on the rear of the No. 1 engine cover. Continue to raise the No. 1 engine cover to detach the 3 clips on the front and side of the No. 1 engine cover and remove the No. 1 engine cover.

      Note

      Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover to break.

  6. REMOVE BATTERY CLAMP SUB-ASSEMBLY


    1. A01IP71

      Remove the bolt and loosen the nut.

    2. Detach the hook of the battery clamp sub-assembly from the battery carrier, and then remove the battery clamp sub-assembly.

  7. REMOVE BATTERY INSULATOR

  8. REMOVE BATTERY

  9. REMOVE BATTERY TRAY

  10. REMOVE BATTERY CARRIER


    1. A01ISD1

      Detach the 2 clamps and disconnect the wire harness.

    2. Remove the 4 bolts and battery carrier.

  11. REMOVE AIR CLEANER CAP SUB-ASSEMBLY


    1. A01IOT2

      Открепите зажим и отсоедините разъем датчика массового расхода воздуха.

    2. Сдвиньте хомут и отсоедините шланг системы принудительной вентиляции картера от крышки головки блока цилиндров.

    3. Сдвиньте хомут и отсоедините шланг воздушного фильтра в сборе от турбонагнетателя.

    4. Освободите 4 зажима и снимите крышку воздушного фильтра в сборе.

  12. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  13. REMOVE AIR CLEANER CASE


    1. A01ITZL

      Выверните 3 болта и снимите корпус воздушного фильтра.

  14. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

    Click here

  15. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

    A01IT4Y

    1. Remove the 3 nuts and front No. 1 floor heat insulator.

  16. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY


    1. A01IPQME02
      Text in Illustration
      *1 Select Cable
      *2 Shift Cable

      Disconnect the control shift cable from the shift lever assembly.

    2. Pinch the areas indicated by the arrows and disconnect the control select cable.

    3. A01IUJQ

      Detach the 2 claws and disconnect the control cable assembly.

    4. A01IUSD

      Remove the 2 clips and disconnect the 2 cables from the transaxle.

    5. A01IUOD

      Remove the 2 clips and disconnect the 2 cables from the control cable bracket.

    6. A01IOIU

      Remove the bolt and detach the bracket of the control cable assembly.

    7. A01IQR5

      Remove the 2 nuts and detach the grommet of the control cable assembly.