TRANSMISSION CONTROL CABLE ADJUSTMENT

PROCEDURE

1. PRECAUTION

   Note

   After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

   Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

   Click here

   Note

   When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

   Click here

3. REMOVE BATTERY

   Click here

4. REMOVE REAR CONSOLE BOX ASSEMBLY

   Click here

5. REMOVE RADIATOR COVER

   Click here

6. REMOVE NO. 1 AIR CLEANER INLET

   Click here

7. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

   Click here

8. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

   Click here

9. REMOVE ECM

   Click here

10. REMOVE BATTERY CLAMP SUB-ASSEMBLY

    Click here

11. SECURE VEHICLE

    
    

    1. Fully apply the parking brake and chock a wheel.

       CAUTION:

       
       

       • 

         Make sure to apply the parking brake and chock a wheel before performing this procedure.

       • If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.

12. ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY

    Tech Tips

    
    

    • After the floor shift shift lever assembly or the transmission control cable assembly is replaced, be sure to adjust the transmission control cable assembly.

    • If the shift lever does not move (or the shift lever is difficult to move) to the 1st or 2nd position, or if it is possible to move the shift lever to the reverse position without pulling up the slider shaft, the length of the transmission control cable assembly must be adjusted.

    
    

    1. 

       Remove the clip to disconnect the transmission control select cable from the floor shift shift lever assembly.

    2. 

       *1	Lock Piece
       *2	Stopper
       *3	Adjuster Case
       *a	Twist the stopper
       *b	Pull out
       *c	Return the stopper

       Release the lock of the transmission control select cable length adjustment structure.

       
       

       1. Twist the stopper.

       2. Pull the lock piece outward from the adjuster case to release the lock.

       3. Return the stopper.

    3. 

       Connect the transmission control select cable to the floor shift lever assembly and install the clip.

       Note

       
       

       • Make sure that the lock piece of the transmission control select cable length adjustment structure is facing upward when the transmission control select cable is connected.

       • Make sure that the transmission control select cable is securely installed.

    4. 

       *1	Outer Lever
       *2	Reverse Restrict Pin Assembly
       *a	Secured

       Hook the outer lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.

    5. 

       *a	Slider Shaft
       *b	Cam Wall

       Push the slider shaft against the cam wall.

       Note

       
       

       • Do not pull up the slider shaft.

       • When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

    6. Lock the transmission control select cable length adjustment structure.

       
       

       1. Twist the stopper.

          

          *1	Lock Piece	*2	Stopper
          *3	Adjuster Case	-	-
          *a	Twist the stopper	*b	Push
          *c	Return the stopper	-	-

       2. Push the lock piece into the adjuster case with slider held against the cam wall.

          Note

          
          

          • Securely press in the lock piece until the lock engages.

          • When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

       3. Return the stopper to prevent the lock from being released.

          Note

          
          

          • Push the lock piece as far as it will go.

          • Confirm whether the transmission control select cable length adjustment structure is locked securely.

    7. 

       *1	Outer Lever
       *2	Reverse Restrict Pin Assembly
       *a	Released

       Move the shift lever to the reverse position, so that the outer lever can be released.

13. INSTALL BATTERY CLAMP SUB-ASSEMBLY

    Click here

14. INSTALL ECM

    Click here

15. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

16. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

17. INSTALL NO. 1 AIR CLEANER INLET

    Click here

18. INSTALL RADIATOR COVER

    Click here

19. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

20. INSTALL BATTERY

    Click here

21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here