DYNAMIC RADAR CRUISE CONTROL SYSTEM Distance Control Switch Circuit

DESCRIPTION

The distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the steering pad switch assembly (distance control switch) while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

A005OE6E04

CAUTION / NOTICE / HINT

Note


  • Before replacing the ECM, refer to Service Bulletin.

  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

    Click here

  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

PROCEDURE


  1. READ VALUE USING GTS (DISTANCE CONTROL SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Radar Cruise 2 / Data List.

    5. Read the Data List according to the display on the GTS.


      Powertrain > Radar Cruise2 > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Distance Control Switch Distance control switch signal ON or OFF

      ON: Distance control switch on

      OFF: Distance control switch off

      		 -

      Powertrain > Radar Cruise2 > Data List
      Tester Display
      Distance Control Switch
      OK
      The Data List item shown in the table changes according to the operation of the steering pad switch assembly (distance control switch).
      Result
      Proceed to
      OK
      NG

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

    NG

  2. INSPECT STEERING PAD SWITCH ASSEMBLY


    1. Remove the steering pad switch assembly.

      Click here

    2. Inspect the steering pad switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE STEERING PAD SWITCH ASSEMBLY Click here

    OK

  3. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. Remove the spiral cable sub-assembly.

      Click here

    2. Inspect the spiral cable sub-assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA, ECM AND BODY GROUND)


    1. Disconnect the spiral cable sub-assembly connector.

    2. Disconnect the forward recognition camera connector.

    3. Disconnect the ECM connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F29-12 (DIST) - R5-3 (LKSW) Always Below 1 Ω
      F29-2 (ECC) - A38-41 (ECCS) Always Below 1 Ω
      F29-12 (DIST) or R5-3 (LKSW) - Body ground Always 10 kΩ or higher
      F29-2 (ECC) or A38-41 (ECCS) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)


    1. Disconnect the C62 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      F29-2 (ECC) or C62-53 (E1) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK ECM (ECM TERMINALS)


    1. Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A38-41 (ECCS) - C62-53 (E1) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FORWARD RECOGNITION CAMERA Click here

    NG

    REPLACE ECM Click here