Note
Before replacing the ECM refer to Service Bulletin.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.
Tech Tips
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.
| Symptom | Suspected Area | Link |
|---|---|---|
| The dynamic radar cruise control system cannot be turned on using the cruise control main switch (ON/OFF button) | CAN communication system | |
| Cruise control switch circuit | ||
| Cruise main indicator light circuit | ||
| Combination meter assembly | ||
| Millimeter wave radar sensor assembly | ||
| ECM | ||
| The dynamic radar cruise control mode cannot be changed between vehicle-to-vehicle distance control mode and constant speed control mode | CAN communication system | |
| Cruise control switch circuit | ||
| Combination meter assembly | ||
| ECM | ||
| The vehicle-to-vehicle distance cannot be changed | CAN communication system | |
| Distance control switch circuit | ||
| Combination meter assembly | ||
| Millimeter wave radar sensor assembly | ||
| Vehicle speed setting cannot be performed (in constant speed control mode) | Fail-safe chart | |
| CAN communication system | ||
| Cruise control switch circuit | ||
| Stop light switch circuit | ||
| Continuously Variable transaxle system (for K313) | ||
| Continuously Variable transaxle system (for K313F) | ||
| Vehicle stability control system | ||
| Millimeter wave radar sensor assembly | ||
| ECM | ||
| Vehicle speed setting cannot be performed (in vehicle-to-vehicle distance control mode) | Perform millimeter wave radar sensor assembly adjustment*1 | |
| Fail-safe chart | ||
| Forward recognition camera is temporarily unavailable | ||
| Millimeter wave radar sensor is dirty | ||
| Millimeter wave radar sensor assembly beam axis not adjusted | ||
| CAN communication system | ||
| Cruise control switch circuit | ||
| Continuously Variable transaxle system (for K313) | ||
| Continuously Variable transaxle system (for K313F) | ||
| Millimeter wave radar sensor assembly | ||
| Forward recognition camera | ||
| Vehicle stability control system | ||
| Combination meter assembly | ||
| ECM | ||
| Control of vehicle speed by the dynamic radar cruise control system is canceled (in constant speed control mode) | Fail-safe chart | |
| CAN communication system | ||
| Cruise control switch circuit | ||
| Stop light switch circuit | ||
| Continuously Variable transaxle system (for K313) | ||
| Continuously Variable transaxle system (for K313F) | ||
| Vehicle stability control system | ||
| Millimeter wave radar sensor assembly | ||
| ECM | ||
| Control of vehicle speed by the dynamic radar cruise control system is canceled (in vehicle-to-vehicle distance control mode) | Perform millimeter wave radar sensor assembly adjustment*1 | |
| Fail-safe chart | ||
| Forward recognition camera is temporarily unavailable | ||
| Millimeter wave radar sensor is dirty | ||
| Millimeter wave radar sensor assembly beam axis not adjusted | ||
| CAN communication system | ||
| Cruise control switch circuit | ||
| Continuously Variable transaxle system (for K313) | ||
| Continuously Variable transaxle system (for K313F) | ||
| Millimeter wave radar sensor assembly | ||
| Forward recognition camera | ||
| Vehicle stability control system | ||
| Combination meter assembly | ||
| ECM | ||
| Hunting/vehicle speed is not constant (in constant speed control mode) | CAN communication system | |
| Vehicle stability control system | ||
| ECM | ||
| Hunting/vehicle speed is not constant (in vehicle-to-vehicle distance control mode) | Millimeter wave radar sensor assembly is dirty | |
| Millimeter wave radar sensor assembly beam axis not adjusted | ||
| CAN communication system | ||
| Vehicle stability control system | ||
| Millimeter wave radar sensor assembly | ||
| ECM | ||
| Pulling the cruise control main switch to CANCEL does not cancel control of vehicle speed by the dynamic radar cruise control system | Cruise control switch circuit | |
| ECM | ||
| Moving the shift lever does not cancel control of vehicle speed by the dynamic radar cruise control system | Park/neutral position switch assembly (for K313) | |
| Park/neutral position switch assembly (for K313F) | ||
| Transmission floor shift assembly (for K313) | ||
| Transmission floor shift assembly (for K313F) | ||
| Continuously Variable transaxle system (for K313) | ||
| Continuously Variable transaxle system (for K313F) | ||
| ECM | ||
| Vehicle speed control by the cruise control system is not canceled when the paddle shift switch is operated | Transmission shift switch circuit (for K313) | |
| Transmission shift switch circuit (for K313F) | ||
| ECM | ||
| Depressing the brake pedal does not cancel control of vehicle speed by the dynamic radar cruise control system | Stop light switch circuit | |
| ECM | ||
| Control cannot be canceled while the vehicle is stopped. | Fail-safe chart | |
| Seat belt warning system | ||
| Theft deterrent system | ||
| Door courtesy switch circuit | ||
| Back door courtesy switch circuit | ||
| Even though the electric parking brake is operating, control cannot be canceled (w/ Full-speed Following Function) | CAN communication system | |
| Parking brake ECU assembly (Brake actuator assembly) (for LHD) | ||
| Parking brake ECU assembly (Brake actuator assembly) (for RHD) | ||
| Millimeter wave radar sensor assembly | ||
| Even though the millimeter wave radar sensor is not dirty, the warning message "Clean Sensor" is displayed | Millimeter wave radar sensor assembly | |
| The vehicle approach warning buzzer does not sound | Skid control buzzer circuit | |
| Check millimeter wave radar sensor assembly installation position | ||
| Check installation of forward recognition camera | ||
| Forward recognition camera | ||
| Millimeter wave radar sensor assembly | ||
| Even though the vehicle approach warning buzzer is sounding, brake control is not performed when decelerating | CAN communication system | |
| Vehicle stability control system | ||
| Millimeter wave radar sensor assembly | ||
| ECM | ||
| Even though the SET function is operating, the cruise SET indicator does not illuminate | CAN communication system | |
| Cruise SET indicator light circuit | ||
| Combination meter assembly | ||
| ECM | ||
| The cruise control indicator remains illuminated | CAN communication system | |
| Combination meter assembly | ||
| ECM | ||
| Indicators are not illuminated on the multi-information display in the combination meter assembly | CAN communication system | |
| Combination meter assembly | ||
| ECM | ||
| The buzzer does not sound when control of vehicle speed by the dynamic radar cruise control is canceled | CAN communication system | |
| Combination meter assembly | ||
| ECM |
*1: If error code 7 is output during beam axis alignment, clear the DTCs and perform beam axis alignment again.