SFI SYSTEM, Diagnostic DTC:P010014

DTC Code DTC Name
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open

DESCRIPTION

Refer to DTC P010012.

Click here

Tech Tips

When P010014 is stored, the ECM enters fail-safe mode. During fail-safe mode, boost prohibited and the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open The mass air flow meter voltage is less than 0.2 V for 3 seconds or more (1 trip detection logic).

  • Open or short in mass air flow meter circuit

  • Mass air flow meter

  • ECM

 Comes on DTC stored SAE Code: P0102

Tech Tips

When this DTC is output, check the mass air flow in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Mass Air Flow Sensor.

DTC No. Mass Air Flow Sensor Malfunction
P010014 0.0 gm/sec

  • Open in mass air flow meter power source circuit

  • Open in VG circuit

  • Short to ground in VG circuit

If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter circuit and stores this DTC.

Example:

When the sensor output voltage remains less than 0.2 V for 3 seconds or more, the ECM stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the ignition switch off and wait for at least 30 seconds.

  6. Turn the ignition switch to ON.

  7. Turn the GTS on.

  8. Wait 5 seconds or more.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes.

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P010014.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

Refer to DTC P010012.

Click here

CAUTION / NOTICE / HINT

Note

Inspect the fuses for circuits related to this system before performing the following procedure.

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)

    A005OMFC88
    *a

    Front view of wire harness connector

    (to Mass Air Flow Meter)

    1. Disconnect the mass air flow meter connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      C6-1 (+B) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK ECM POWER SOURCE CIRCUIT Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)


    1. Disconnect the C6 mass air flow meter connector.

    2. Disconnect the C62 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C6-3 (VG) - C62-92 (VG) Always Below 1 Ω
      C6-3 (VG) or C62-92 (VG) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT MASS AIR FLOW METER


    1. Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter.

      Click here

    2. Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter.

      Click here

    3. Inspect the function of the mass air flow meter.


      1. Connect the GTS to the DLC3.

      2. Turn the ignition switch to ON.

      3. Turn the GTS on.

      4. Enter the following menus: Powertrain / Engine / Data List / All Data / Mass Air Flow Sensor.


        Powertrain > Engine > Data List
        Tester Display
        Mass Air Flow Sensor

      5. Start the engine.

      6. Check that the Mass Air Flow Sensor value changes when the engine is raced.

        OK
        The reading changes.

        Tech Tips

        Perform "Inspection After Repair" after replacing the mass air flow meter.

        Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPLACE MASS AIR FLOW METER Click here