REAR SEAT OUTER BELT ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Intelligent clearance sonar system*1
Simple intelligent parking assist system*1
Pre-crash safety system
Parking assist monitor system

Click here

Initialize back door lock Power door lock control system

Click here

*1: When performing learning using the GTS.

Click here

CAUTION:


  • B006IJ0

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    • If an SRS part is accidentally deployed, it may cause a serious injury.

    B006IKV

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE TONNEAU COVER ASSEMBLY

    Click here

  4. REMOVE REAR NO. 2 FLOOR BOARD

    Click here

  5. REMOVE REAR NO. 4 FLOOR BOARD

    Click here

  6. REMOVE REAR NO. 3 FLOOR BOARD

    Click here

  7. REMOVE REAR NO. 1 FLOOR BOARD

    Click here

  8. REMOVE DECK FLOOR BOX LH

    Click here

  9. REMOVE DECK FLOOR BOX RH

    Click here

  10. REMOVE DECK TRIM SERVICE HOLE COVER

    Click here

  11. REMOVE REAR DECK TRIM COVER

    Click here

  12. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

    Click here

  13. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

    Click here

  14. REMOVE REAR SEATBACK ASSEMBLY LH (for LH Side)

    Click here

  15. REMOVE REAR SEATBACK HINGE COVER (for RH Side)

    Click here

  16. REMOVE REAR SEATBACK ASSEMBLY RH (for RH Side)

    Click here

  17. REMOVE REAR SEAT CUSHION ASSEMBLY LH (for LH Side)

    Click here

  18. REMOVE REAR SEAT CUSHION ASSEMBLY RH (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  19. REMOVE REAR SEAT CUSHION LOCK HOOK

    Click here

  20. REMOVE REAR DOOR SCUFF PLATE

    Click here

  21. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

    Click here

  22. REMOVE REAR UNDER SIDE COVER

    Click here

  23. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY

    Click here

  24. REMOVE REAR SEAT SIDE GARNISH

    Click here

  25. REMOVE ROPE HOOK (w/o Toyota Safety Sense)

    Click here

  26. REMOVE NO. 2 ROPE HOOK (w/o Toyota Safety Sense)

    Click here

  27. REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/ Toyota Safety Sense)

    Click here

  28. REMOVE TONNEAU COVER HOOK A (w/ Toyota Safety Sense)

    Click here

  29. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for RH Side)

    Click here

  30. REMOVE DECK TRIM SIDE PANEL ASSEMBLY

    Click here

  31. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY

    Click here

  32. REMOVE REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY LH (for LH Side)


    1. B006HOP

      Remove the bolt to disconnect the floor anchor of the rear 3 point type seat outer belt assembly LH.

    2. B006I6IC03
      *a Locking Button
      *b Protective Tape
      *c Release

      Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

      Tech Tips

      Tape the screwdriver tip before use.

    3. B006IQ1

      Remove the 3 bolts.

    4. Disengage the 3 guides to remove the rear 3 point type seat outer belt assembly LH.

  33. REMOVE REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY RH (for RH Side)


    1. B006I1D

      Remove the bolt to disconnect the floor anchor of the rear 3 point type seat outer belt assembly RH.

    2. B006IRB

      Remove the 3 bolts.

    3. Disengage the 3 guides.

    4. B006I2ZC03
      *a Locking Button
      *b Protective Tape
      *c Release

      Disengage the clamp.

    5. Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

      Tech Tips

      Tape the screwdriver tip before use.

    6. Remove the rear 3 point type seat outer belt assembly RH.