PRE-CRASH SAFETY SYSTEM, Diagnostic DTC:U1104

DTC Code DTC Name
U1104 Lost Communication with Driving Support ECU

DESCRIPTION

The driving support ECU assembly is connected to the millimeter wave radar sensor assembly, forward recognition camera and skid control ECU (brake booster with master cylinder assembly) via CAN communication. If communication with the millimeter wave radar sensor assembly, forward recognition camera or skid control ECU (brake booster with master cylinder assembly) stops, the driving support ECU assembly stores DTC U1104.

DTC No. Detection Item DTC Detection Condition Trouble Area
U1104 Lost Communication with Driving Support ECU

Any of the following conditions is met:


  • When the power switch is on (IG), a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds.

  • When the power switch is on (IG), a communication error between the driving support ECU assembly and the forward recognition camera is detected for approximately 0.3 seconds.

  • When the power switch is on (IG), a communication error between the driving support ECU assembly and the skid control ECU (brake booster with master cylinder assembly) is detected for approximately 1.5 seconds.


  • CAN communication system

  • Millimeter wave radar sensor assembly

  • Forward recognition camera

  • Skid control ECU (Brake booster with master cylinder assembly)

  • Driving support ECU assembly

  • Wire harness or connector

CAUTION / NOTICE / HINT

Note


  • When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

  • If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

    Click here

  • When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

  • When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

    Click here

  • Confirm that the connectors are securely connected, as a partially connected connector can cause this DTC to be stored.

PROCEDURE


  1. CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)


    1. Check for DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Trouble Codes
      Result
      Result Proceed to
      DTC U1104 and other DTCs are output A
      Only DTC U1104 is output B

    A
    B
  2. CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)


    1. Check for DTCs.

      Click here


      Chassis > Front Recognition Camera > Trouble Codes
      Result
      Result Proceed to
      Forward recognition camera system DTCs are not output A
      Forward recognition camera system DTCs are output B

    B
    A
  3. CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)


    1. Check for DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      Electronically controlled brake system DTC are not output A
      Electronically controlled brake system DTC are output B

    B
    A
  4. TEST MODE INSPECTION (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

    Tech Tips

    When entering test mode, the skid control ECU (brake booster with master cylinder assembly) communicates with the driving support ECU assembly to judge whether the vehicle is equipped with the pre-crash safety system. Therefore, do not exit test mode within 5 seconds of entering test mode.


    1. Procedure to Enter Test Mode (Signal Check)


      1. Turn the power switch off.

      2. Check that the steering wheel is centered.

      3. Check that park (P) is selected.

      4. Connect the GTS to the DLC3.

      5. Turn the power switch on (IG).

      6. Turn the GTS on.

      7. Switch the skid control ECU (brake booster with master cylinder assembly) to Test Mode (Signal Check) using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

        Tech Tips

        Do not exit test mode within 5 seconds of entering test mode. If test mode is exited within 5 seconds of entering test mode, DTC U1104 may be stored. If DTC U1104 is output after exiting test mode, enter test mode again, wait at least 5 seconds, then recheck for DTCs.


        Chassis > ABS/VSC/TRC > Utility
        Tester Display
        Signal Check
    2. Test Mode (Signal Check) Display Check


      1. Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.

        Tech Tips

        If the ABS warning light, brake warning light / yellow (minor malfunction) or slip indicator light remains illuminated or does not illuminate when Test Mode (Signal Check) is entered, a component or wire harness may be malfunctioning.

    3. End of Test Mode (Signal Check)


      1. Turn the power switch off and disconnect the GTS.

      Result
      Proceed to
      NEXT

    NEXT
  5. CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)


    1. Clear the DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Clear DTCs
    2. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Turn the power switch on (IG) and wait 1.5 seconds or more.

    3. Check for DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Trouble Codes
      Result
      Result Proceed to
      DTC U1104 is not output A
      DTC U1104 is output B

    A
    B
  6. REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY


    1. Replace the millimeter wave radar sensor assembly.

      Click here

    2. Adjust the millimeter wave radar sensor assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT
  7. CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)


    1. Clear the DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Clear DTCs
    2. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Turn the power switch on (IG) and wait 1.5 seconds or more.

    3. Check for DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Trouble Codes
      Result
      Result Proceed to
      DTC U1104 is not output A
      DTC U1104 is output B

    A
    B
  8. REPLACE DRIVING SUPPORT ECU ASSEMBLY


    1. Replace the driving support ECU assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT
  9. CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)


    1. Clear the DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Clear DTCs
    2. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Turn the power switch on (IG) and wait 1.5 seconds or more.

    3. Check for DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Trouble Codes
      Result
      Result Proceed to
      DTC U1104 is not output A
      DTC U1104 is output B

    A
    B
  10. REPLACE FORWARD RECOGNITION CAMERA


    1. Replace the forward recognition camera.

      Click here

    2. Perform Forward Recognition Camera Learning.

      Click here

      Result
      Proceed to
      NEXT

    NEXT
  11. CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)


    1. Clear the DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Clear DTCs
    2. Perform the following procedure.

      Tech Tips

      If the following procedure is not performed, the previously output DTC cannot be detected.


      1. Turn the power switch on (IG) and wait 1.5 seconds or more.

    3. Check for DTCs.

      Click here


      Body Electrical > Pre-Crash 2 > Trouble Codes
      Result
      Result Proceed to
      DTC U1104 is not output A
      DTC U1104 is output B

    A
    B
  12. REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)


    1. Replace the skid control ECU (brake booster with master cylinder assembly).


      Result
      Proceed to
      NEXT

    NEXT