AIRBAG SYSTEM, Diagnostic DTC:B1830/57

DTC Code DTC Name
B1830/57 Short in Curtain Shield Squib RH Circuit

DESCRIPTION

The curtain shield squib RH circuit consists of the airbag sensor assembly and curtain shield airbag assembly RH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

DTC B1830/57 is stored when a line short is detected in the curtain shield squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1830/57 Short in Curtain Shield Squib RH Circuit

  • The airbag sensor assembly detects a line short in the curtain shield squib RH circuit during primary check.

  • Curtain shield squib RH malfunction

  • Airbag sensor assembly malfunction

  • No. 2 floor wire

  • Curtain shield squib RH (Curtain shield airbag assembly RH)

  • Airbag sensor assembly

 Applies to check mode

WIRING DIAGRAM

A01MIN8E03
*a Curtain shield Squib RH (Curtain shield Airbag Assembly RH)
*b Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

Tech Tips


  • Perform the simulation method by selecting check mode (Signal Check) using the GTS.

    Click here

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

    Click here

PROCEDURE


  1. CHECK CONNECTORS


    1. A01MJMXC01
      *1 Curtain Shield Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the curtain shield airbag assembly RH and airbag sensor assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the curtain shield airbag assembly RH and airbag sensor assembly.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the No. 2 floor wire connector (on the curtain shield airbag assembly RH side) is not damaged.

      OK
      The connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short spring for the No. 2 floor wire with the activation prevention mechanism is not deformed or damaged.

      OK
      The short spring is not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  2. CHECK NO. 2 FLOOR WIRE


    1. A01MFV3C01
      *1 Curtain Shield Airbag Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Curtain Shield Airbag Assembly RH)

      Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B.

        Click here

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        Q6-1 (ICR+) - Q6-2 (ICR-) Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  3. CHECK DTC


    1. A01MJQOC01
      *1 Curtain Shield Airbag Assembly RH
      *2 Airbag Sensor Assembly

      Connect the connectors to the airbag sensor assembly.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Turn the power switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      OK
      DTC B1830/57 is not output.

      Tech Tips

      Codes other than DTC B1830/57 may be output at this time, but they are not related to this check.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    OK

  4. CHECK DTC


    1. A01MHMPC01
      *1 Curtain Shield Airbag Assembly RH
      *2 Airbag Sensor Assembly

      Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal and wait for at least 90 seconds.

    3. Connect the connectors to the curtain shield airbag assembly RH.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    7. Turn the power switch off.

    8. Turn the power switch on (IG), and wait for at least 60 seconds.

    9. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      OK
      DTC B1830/57 is not output.

      Tech Tips

      Codes other than DTC B1830/57 may be output at this time, but they are not related to this check.

      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH Click here