PARKING BRAKE ASSEMBLY DISASSEMBLY

CAUTION / NOTICE / HINT

Note


  • When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTCs.

  • While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.

Tech Tips


  • The following procedure is for the LH side.

  • Use the same procedure for the RH and LH sides.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

    Click here

  2. DISABLE BRAKE CONTROL

    Click here

  3. REMOVE REAR WHEEL

    Click here

  4. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  5. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE PLUG

    Click here

  6. REMOVE REAR DISC

    Click here

  7. REMOVE NO. 3 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01MJWN

      Remove the No. 3 parking brake shoe return tension spring.

  8. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01MFQ0

      Remove the No. 1 parking brake shoe return tension spring.

  9. REMOVE BRAKE SHOE HOLD DOWN SPRING (for Front Side)


    1. A01MI8TE01

      Using SST, rotate the parking brake shoe hold down spring pin, and remove the brake shoe hold down spring.

      SST
      09718-00011

  10. REMOVE PARKING BRAKE SHOE STRUT


    1. A01MJ8C

      Pull the No. 1 parking brake shoe assembly towards the front of the vehicle as shown in the illustration.

    2. A01MJQV

      Remove the parking brake shoe strut.

  11. REMOVE BRAKE SHOE HOLD DOWN SPRING (for Rear Side)


    1. A01MJD2E01

      Using SST, rotate the parking brake shoe hold down spring pin, and remove the brake shoe hold down spring.

      SST
      09718-00011

  12. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET


    1. A01MH1H

      Expand the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly outward and pull downward to separate them from the parking brake plate sub-assembly as shown in the illustration.

    2. A01MIW4

      Remove the parking brake shoe adjusting screw set from the No. 1 parking brake shoe assembly and No. 2 parking brake shoe assembly.

  13. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY


    1. A01MIQB

      Remove the No. 1 parking brake shoe assembly from the No. 2 parking brake shoe return tension spring.

  14. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING


    1. A01MI3Y

      Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.

  15. SEPARATE PARKING BRAKE SHOE LEVER


    1. A01MI3R

      Using needle-nose pliers, separate the parking brake shoe lever from the No. 3 parking brake cable assembly.

  16. REMOVE PARKING BRAKE SHOE LEVER


    1. A01MJ9G

      Expand the parking brake shoe type C washer to remove it from the No. 2 parking brake shoe assembly as shown in the illustration.

    2. Remove the parking brake shoe lever and parking brake shoe shim from the No. 2 parking brake shoe assembly.

      Tech Tips

      Parking brake shoe shims are provided when necessary to adjust the clearance between the parking brake shoe lever and parking brake shoe type C washer. Some vehicles may not be equipped with shims.

  17. REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Front Side)


    1. A01MIPA

      Remove the parking brake shoe hold down spring pin of the front side from the parking brake plate sub-assembly.

  18. REMOVE PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for Rear Side)


    1. Remove the rear axle hub and bearing assembly.

      Click here

    2. A01MIPG

      Remove the nut to separate the parking brake plate sub-assembly from the rear axle beam assembly.

      Note

      Hang the parking brake plate sub-assembly using a wire or an equivalent tool.

    3. A01MFJF

      Remove the parking brake shoe hold down spring pin of the rear side from the parking brake plate sub-assembly.