ROOF HEADLINING(for Single Cab) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart.

    Click here

PROCEDURE


  1. INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. B0027ZQ

      Attach the claw to install the rear side rail spacer LH.

  2. INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)


    1. B00291A

      Attach the claw to install the rear side rail spacer RH.

  3. INSTALL FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)


    1. B00260K

      Attach the claw to install the front side rail spacer LH.

  4. INSTALL FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)


    1. B0024KW

      Attach the claw to install the front side rail spacer RH.

  5. INSTALL ROOF HEADLINING ASSEMBLY


    1. w/ Overhead Console:


      1. B002571C01
        B0069FO Movement Direction

        Insert the roof headlining assembly into the cabin from the front door.

        Note


        • Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

        • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

        • Do not damage the roof headlining assembly or vehicle interior.

      2. B0025Y0

        Install the visor holder as shown in the illustration.

      3. B0027JRC01
        B0069FO Install in this Direction

        Attach the claw to install the visor holder as shown in the illustration.

        Tech Tips

        Use the same procedure for both visor holders.

      4. B002493

        Install the roof headlining assembly with the 3 clips.

    2. w/o Overhead Console:


      1. B0027VVC01
        B0069FO Movement Direction

        Insert the roof headlining assembly into the cabin from the front door.

        Note


        • Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.

        • Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

        • Do not damage the roof headlining assembly or vehicle interior.

      2. B0025Y0

        Install the visor holder as shown in the illustration.

      3. B0027JRC01
        B0069FO Install in this Direction

        Attach the claw to install the visor holder as shown in the illustration.

        Tech Tips

        Use the same procedure for both visor holders.

      4. B00245H

        Install the roof headlining assembly with the 3 clips.

    3. B0028MDC01
      *1 Front Door Opening Trim Weatherstrip LH

      Connect the front door opening trim weatherstrip LH in the range shown in the illustration.

    4. B0025GTC01
      *1 Front Door Opening Trim Weatherstrip RH

      Connect the front door opening trim weatherstrip RH in the range shown in the illustration.

    5. w/ Pre-crash Safety System:


      1. B0025PK

        w/ Camera Heater:

        Connect the 2 connectors.

      2. B00263F

        w/o Camera Heater:

        Connect the connector.

    6. w/o Pre-crash Safety System:


      1. B0027M0

        Connect the connector and attach the clamp to the front pillar LH.

    7. w/ Pre-crash Safety System:


      1. B0026T9

        Connect the connector and attach the clamp to the front pillar LH.

  6. INSTALL ROOF HEADLINING SERVICE HOLE COVER (w/o Assist Grip)


    1. B00278A

      Install the 2 roof headlining service hole covers.

  7. INSTALL ASSIST GRIP SUB-ASSEMBLY

    Tech Tips

    w/ Assist Grip:

    Use the same procedure for both assist grip sub-assemblies.


    1. B0026VD

      Install the assist grip sub-assembly with the 2 bolts.

    2. B0025IN

      Attach the claw to close the assist grip cover.

  8. INSTALL VISOR ASSEMBLY LH


    1. B0027W6

      Install the visor assembly LH with the 2 screws.

    2. Connect the visor assembly LH to the visor holder.

  9. INSTALL VISOR ASSEMBLY RH


    1. B0025D8

      Install the visor assembly RH with the 2 screws.

    2. Connect the visor assembly RH to the visor holder.

  10. INSTALL VISOR BRACKET COVER LH


    1. B0025OEC01
      B0069FO Install in this Direction

      Attach the claw to install the visor bracket cover LH as shown in the illustration.

  11. INSTALL VISOR BRACKET COVER RH


    1. B00250ZC01
      B0069FO Install in this Direction

      Attach the claw to install the visor bracket cover RH as shown in the illustration.

  12. INSTALL NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)

    Click here

  13. INSTALL MAP LIGHT ASSEMBLY


    1. w/ Overhead Console:

      Click here

    2. w/o Overhead Console:

      Click here

  14. INSTALL QUARTER INSIDE TRIM BOARD LH


    1. B0025MZC01
      B0069FO Install in this Direction

      Attach the clip to install the quarter inside trim board LH as shown in the illustration.

    2. B00278MC01
      *1 Front Door Opening Trim Weatherstrip LH

      Connect the front door opening trim weatherstrip LH in the range shown in the illustration.

    3. B0024CM

      Connect the front seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  15. INSTALL QUARTER INSIDE TRIM BOARD RH


    1. B00271VC01
      B0069FO Install in this Direction

      Attach the clip to install the quarter inside trim board RH as shown in the illustration.

    2. B002933C01
      *1 Front Door Opening Trim Weatherstrip RH

      Connect the front door opening trim weatherstrip RH in the range shown in the illustration.

    3. B00290U

      Connect the front seat outer belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  16. INSTALL SEAT BELT ANCHOR COVER CAP

    Tech Tips

    Use the same procedure for both seat belt anchor cover caps.


    1. B0024NWC01
      B0069FO Install in this Direction

      Attach the claw to install the seat belt anchor cover cap as shown in the illustration.

  17. INSTALL LOWER QUARTER TRIM PANEL LH


    1. B0024G1C01
      B0069FO Install in this Direction

      Attach the clip and claw to install the lower quarter trim panel LH as shown in the illustration.

    2. B0028HO

      Connect the front seat outer belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. B0024J6C01
      *1 Front Door Opening Trim Weatherstrip LH

      Connect the front door opening trim weatherstrip LH in the range shown in the illustration.

  18. INSTALL LOWER QUARTER TRIM PANEL RH


    1. B00268KC01
      B0069FO Install in this Direction

      Attach the clip and claw to install the lower quarter trim panel RH as shown in the illustration.

    2. B002487

      Connect the front seat outer belt assembly RH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. B0026J0C01
      *1 Front Door Opening Trim Weatherstrip RH

      Connect the front door opening trim weatherstrip RH in the range shown in the illustration.

  19. INSTALL UPPER BACK PANEL GARNISH


    1. B002953C01
      B0069FO Install in this Direction

      Attach the clip and claw to install the upper back panel garnish as shown in the illustration.

      Tech Tips

      Lower the claw into position to attach it.

  20. INSTALL FRONT DOOR SCUFF PLATE LH


    1. B0024O9C01
      B0069FO Install in this Direction

      Attach the clip and claw to install the front door scuff plate LH as shown in the illustration.

  21. INSTALL FRONT DOOR SCUFF PLATE RH


    1. B0027EPC01
      B0069FO Install in this Direction

      Attach the clip and claw to install the front door scuff plate RH as shown in the illustration.

  22. INSTALL FRONT PILLAR GARNISH LH

    Click here

  23. INSTALL FRONT PILLAR GARNISH RH

    Click here

  24. INSTALL ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

    Click here

  25. INSTALL FRONT SEAT ASSEMBLY LH


    1. for Manual Seat:

      Click here

    2. for Bench Seat Type:

      Click here

  26. INSTALL FRONT SEAT ASSEMBLY RH

    Click here

  27. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Airbag System)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  28. CHECK SRS WARNING LIGHT (w/ Airbag System)

    Click here