Click here

POWER POINT SOCKET(for Double Socket Type) REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 1 power outlet socket assembly removal/installation are shown below.

Table 1. Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here
Memorize steering angle neutral point Pre-collision system

Click here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

Click here

PROCEDURE


  1. Click here

    PRECAUTION (w/ Airbag System)

    CAUTION:
    B0069A2

    Be sure to read Precaution thoroughly before servicing.

    for Type A:

    Click here

    for Type B:

    Click here

    for Type C:

    Click here

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. Click here

    DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

    CAUTION:
    B00693Q

    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. Click here

    REMOVE STEERING WHEEL ASSEMBLY

    Click here

  4. Click here

    REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

    Click here

  5. Click here

    REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

    Click here

  6. Click here

    REMOVE CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

    Click here

  7. Click here

    REMOVE CONTROL KNOB SUB-ASSEMBLY


    1. for Manual Cooler System:

      Click here

    2. for Manual Air Conditioning System:

      Click here

  8. Click here

    REMOVE AIR INLET DAMPER CONTROL LEVER


    1. for Manual Cooler System:

      Click here

    2. for Manual Air Conditioning System:

      Click here

  9. Click here

    REMOVE INTEGRATION PANEL SUB-ASSEMBLY


    1. for Manual Cooler System:

      Click here

    2. for Manual Air Conditioning System:

      Click here

  10. Click here

    REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

    Click here

  11. Click here

    REMOVE STEERING COLUMN LOWER COVER

    Click here

  12. Click here

    REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

    Click here

  13. Click here

    REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (w/ Knee Airbag)

    Click here

  14. Click here

    REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

    Click here

  15. Click here

    REMOVE LOWER INSTRUMENT COVER SUB-ASSEMBLY

    Click here

  16. Click here

    REMOVE NO. 1 POWER OUTLET SOCKET ASSEMBLY

    Tip:

    Use the same procedure for both power outlet socket assemblies.


    1. B0025I8C02
      B00692L Protective Tape
      B0069FO Remove in this Direction

      Using a thin-bladed screwdriver, detach the claw, and remove the No. 1 power outlet socket assembly as shown in the illustration.

      Tip:

      Tape the thin-bladed screwdriver tip before use.

  17. Click here

    REMOVE NO. 1 POWER OUTLET SOCKET COVER

    Tip:

    Use the same procedure for both power outlet socket covers.


    1. B0027KOC02
      B0069FO Remove in this Direction

      Detach the claw and remove the No. 1 power outlet socket cover as shown in the illustration.