POWER POINT SOCKET(for Double Socket Type) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 1 power outlet socket assembly removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Pre-crash safety system

Click here

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

PROCEDURE


  1. PRECAUTION (w/ Airbag System)

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    B0069A2

    for Type A:

    Click here

    for Type B:

    Click here

    for Type C:

    Click here

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B00693Q

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  4. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

    Click here

  5. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

    Click here

  6. REMOVE CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

    Click here

  7. REMOVE CONTROL KNOB SUB-ASSEMBLY


    1. for Manual Cooler System:

      Click here

    2. for Manual Air Conditioning System:

      Click here

  8. REMOVE AIR INLET DAMPER CONTROL LEVER


    1. for Manual Cooler System:

      Click here

    2. for Manual Air Conditioning System:

      Click here

  9. REMOVE INTEGRATION PANEL SUB-ASSEMBLY


    1. for Manual Cooler System:

      Click here

    2. for Manual Air Conditioning System:

      Click here

  10. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

    Click here

  11. REMOVE STEERING COLUMN LOWER COVER

    Click here

  12. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

    Click here

  13. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIR BAG ASSEMBLY (w/ Knee Airbag)

    Click here

  14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

    Click here

  15. REMOVE LOWER INSTRUMENT COVER SUB-ASSEMBLY

    Click here

  16. REMOVE NO. 1 POWER OUTLET SOCKET ASSEMBLY

    Tech Tips

    Use the same procedure for both power outlet socket assemblies.


    1. B0025I8C02
      B00692L Protective Tape
      B0069FO Remove in this Direction

      Using a thin-bladed screwdriver, detach the claw, and remove the No. 1 power outlet socket assembly as shown in the illustration.

      Tech Tips

      Tape the thin-bladed screwdriver tip before use.

  17. REMOVE NO. 1 POWER OUTLET SOCKET COVER

    Tech Tips

    Use the same procedure for both power outlet socket covers.


    1. B0027KOC02
      B0069FO Remove in this Direction

      Detach the claw and remove the No. 1 power outlet socket cover as shown in the illustration.