LOWER INSTRUMENT PANEL REMOVAL

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the lower instrument panel removal/installation are shown below.

Necessary Procedures after parts removed / installed / replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

Click here

Memorize steering angle neutral point Pre-collision system

Click here

CAUTION:

w/ Airbag System:

B0027VM

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

PROCEDURE


  1. TABLE OF BOLT, SCREW, NUT AND CLIP

    Tech Tips

    All bolts, screws and clips relevant to installing and removing the instrument panel are shown along with their alphabetic code in the table below.

    B0024Y7E01
  2. PRECAUTION (w/ Airbag System)

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

  5. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

    Click here

  6. REMOVE REAR CONSOLE BOX SUB-ASSEMBLY (w/ Rear Console Box)

    Click here

  7. REMOVE FRONT CONSOLE BOX (w/o Console Box Lid)

    Click here

  8. REMOVE HEADLIGHT DIMMER SWITCH ASSEMBLY

    Click here

  9. REMOVE CONTROL KNOB SUB-ASSEMBLY (for Manual Cooler System, for Manual Air Conditioning System)

    Click here

  10. REMOVE INTEGRATION PANEL SUB-ASSEMBLY (for Manual Cooler System, for Manual Air Conditioning System)

    Click here

  11. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

    Click here

  12. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. w/o Audio:


      1. B00255Q

        Remove the 4 screws.

      2. B0026QYC01
        B0068AS Place Hands Here
        B0069FO Remove in this Direction

        Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide.

      3. Disconnect the connector and remove the center instrument cluster finish panel assembly.

    2. w/ Audio, for Radio Receiver Type:


      1. B0026ZE

        Remove the 4 screws.

      2. B00286JC01
        B0068AS Place Hands Here
        B0069FO Remove in this Direction

        Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide.

      3. Disconnect the connector and remove the center instrument cluster finish panel assembly.

    3. w/ Audio, for Radio and Display Type:


      1. B0027IK

        Remove the 4 screws.

      2. B0027PWC01
        B0068AS Place Hands Here
        B0069FO Remove in this Direction

        Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide.

      3. Disconnect the connector and remove the center instrument cluster finish panel assembly.

    4. w/ Audio, for Navigation Receiver Type:


      1. B0024O3

        Remove the 4 screws.

      2. B0024QRC01
        B0068AS Place Hands Here
        B0069FO Remove in this Direction

        Place your hands at the position shown in the illustration and pull as shown to detach the clip and guide.

      3. Disconnect the connector and remove the center instrument cluster finish panel assembly.

  13. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)


    1. B0027A5C01
      *a Screw <A>

      Remove the 2 screws <A>.

    2. B0025H1C01
      B0068AS Place Hands Here
      B0069FO Remove in this Direction

      Place your hands at the position shown in the illustration and pull as shown to detach the clip, claw and guide.

    3. Detach the claw and disconnect the DLC3 and remove the No. 1 instrument panel under cover sub-assembly.

  14. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

    Click here

  15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)


    1. B0024UOC01
      *a Protective Tape
      *b Screw <A>

      Put protective tape around the lower instrument panel finish panel sub-assembly.

    2. Remove the 2 screws <A>.

    3. B0028FNC01
      B0068AS Place Hands Here
      B0069FO Remove in this Direction

      Place your hands at the position shown in the illustration and pull as shown to detach the clip and claw.

    4. Detach the claw and disconnect the DLC3 and remove the lower instrument panel finish panel sub-assembly.

  16. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B00284CC01
      B0069FO Remove in this Direction

      Detach the claw and pull as shown in the illustration.

    2. B00287CC01
      B0069FO Remove in this Direction

      Pull as shown in the illustration, detach the guide and remove the No. 2 instrument panel under cover sub-assembly.

  17. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. B0027HXC01
      B0069FO Remove in this Direction

      Twist the glove door stopper pin as shown in the illustration and remove it.

      Tech Tips

      Use the same procedure for both glove door stopper pins.

    2. B0027MG

      Open the glove compartment door assembly, detach the claw and disconnect the glove compartment door stopper sub-assembly.

      Tech Tips

      Pull diagonally to remove the glove compartment door stopper sub-assembly.

    3. B0027CEC01
      B0069FO Remove in this Direction

      Pull as shown in the illustration to detach the hinge and remove the glove compartment door assembly.

  18. REMOVE LOWER INSTRUMENT COVER SUB-ASSEMBLY


    1. B0026X0C01
      *a Protective Tape

      Put protective tape around the lower instrument cover sub-assembly.

    2. B0028HAC01
      B0068AS Place Hands Here
      B0069FO Remove in this Direction

      Place your hands at the position shown in the illustration and pull as shown to detach the clip and claw.

    3. Disconnect the connector and remove the lower instrument cover sub-assembly.

  19. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    1. B0025UG

      Detach the claw and remove the glove compartment door stopper sub-assembly.

  20. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Remove the 7 screws <B>, 2 bolts <C> and screw <D>.

    2. Detach the guide and disconnect the connector.

      B0025WDC01
      *a Screw <B> *b Bolt <C>
      *c Screw <D> *d Guide
    3. B0024H7

      Detach the claw and guide to disconnect the hood lock control lever sub-assembly and fuel lid lock open lever.

    4. B00263X

      Disconnect the hood lock control cable and fuel lid lock open cable and remove the lower instrument panel sub-assembly.